Frabjousdae
Member
I built this about 7 years ago based on Kal’s site. I brewed about 10-15 batches on this and haven’t brewed at all in the last in several years. I’m looking at making an office shed and the wife says I’ve got to sell this before I can get moving on that. I’m located in the Lehigh Valley in Pennsylvania and would much prefer to sell as a whole, but piece it out.
Price as a whole is $1300
30 amp Kal Clone Panel: $700
Control panel built from Kal’s design
(3) MyPin TD4-SNR PID temperature controller
(3) Temp probes of 7’ length
(2) Receptacles for HLT and Boil Kettles
(2) Receptacles for pumps
Volt and amp meters installed, but not wired
Alarms wired, but never used
Boil Kettle – 15 Gallon: $130
Bayou Classic Stainless Steel Kettle
5500W Stainless Steel heating element (ULWD)
Valve at top of kettle
Valve at bottom of kettle with temperature sensor input
Temperature gauge
False bottom
Mesh Screen
Stainless Steel Kettle Cover
Mash Tun – 15 Gallon: $100
Bayou Classic Stainless Steel Kettle
Valve at top of kettle
Valve at bottom of kettle with temperature sensor input
Temperature gauge
False bottom
Mesh Screen
Stainless Steel Kettle Cover
HERMS HLT – 12.5 Gallon: $100
Stainless Steel Kettle
HERMS coil with valve inlets and outlets (homemade…not the most beautiful or painless)
5500W Stainless Steel heating element (ULWD)
3 Piece ball valve at bottom of kettle with temperature sensor input
Stainless Steel Kettle Cover
2 Chugger Pumps: $125 total
1/20th horsepower
115V and 1.4amp
Model CPPS-IN-1
Counterflow chiller: $30
Homemade 25’ with copper coiled into hosing
Brew Stand: $200
Wood and built based on Kal’s design
Ventilation and Fan: $50
Vortex VTX600
Homemade vent and ducting
Fermenting, Carbonating and Other: $180
(2) 5 gallon Corny Kegs with fittings
C02 tank
CO2 pressure regulator
(2) Better bottles
(8) Swing top bottles
(5) 5 gallon buckets
(3) Bucket small
45 Bottle tree dryer
Bottle cap crimper
Refractometer
Mesh hop infuser
Various tubing
Price as a whole is $1300
30 amp Kal Clone Panel: $700
Control panel built from Kal’s design
(3) MyPin TD4-SNR PID temperature controller
(3) Temp probes of 7’ length
(2) Receptacles for HLT and Boil Kettles
(2) Receptacles for pumps
Volt and amp meters installed, but not wired
Alarms wired, but never used
Boil Kettle – 15 Gallon: $130
Bayou Classic Stainless Steel Kettle
5500W Stainless Steel heating element (ULWD)
Valve at top of kettle
Valve at bottom of kettle with temperature sensor input
Temperature gauge
False bottom
Mesh Screen
Stainless Steel Kettle Cover
Mash Tun – 15 Gallon: $100
Bayou Classic Stainless Steel Kettle
Valve at top of kettle
Valve at bottom of kettle with temperature sensor input
Temperature gauge
False bottom
Mesh Screen
Stainless Steel Kettle Cover
HERMS HLT – 12.5 Gallon: $100
Stainless Steel Kettle
HERMS coil with valve inlets and outlets (homemade…not the most beautiful or painless)
5500W Stainless Steel heating element (ULWD)
3 Piece ball valve at bottom of kettle with temperature sensor input
Stainless Steel Kettle Cover
2 Chugger Pumps: $125 total
1/20th horsepower
115V and 1.4amp
Model CPPS-IN-1
Counterflow chiller: $30
Homemade 25’ with copper coiled into hosing
Brew Stand: $200
Wood and built based on Kal’s design
Ventilation and Fan: $50
Vortex VTX600
Homemade vent and ducting
Fermenting, Carbonating and Other: $180
(2) 5 gallon Corny Kegs with fittings
C02 tank
CO2 pressure regulator
(2) Better bottles
(8) Swing top bottles
(5) 5 gallon buckets
(3) Bucket small
45 Bottle tree dryer
Bottle cap crimper
Refractometer
Mesh hop infuser
Various tubing
Attachments
Last edited: