Search results

The picture of your PID looks like mine (AUBER SYL-2352) and I am also using an RTD-vs-Thermocouple. If you are using the same PID, then connect the red wires to lugs 3 and 4 (doesn't matter which one goes where) and the white wire to the lug 5. Cheers! -Dixon

I see now...I guess I didn't see the input power from the wall to B and C of the bus. Thanks for helping me understand. -Dixon

I am a little confused by the schematic. I thought the use of an SSR was because most PID's can not handle the current from a heating element. It looks to me like the PID is powering the element through terminals 9 and 10, so wouldn't the PID be taking the full load from the element still...

I've had the same question for a while... I'm pretty sure I remember Yuri mentioning saving his for an upcoming project, but never heard anything afterwards. -Dixon

Wow, those QDs are a lot cheaper than what I've been able to find, thanks. I have been told to get a type "T" thermocouple. Does it matter what type I use or is it just based on how I want it mounted? Anyone know any places to buy march pumps cheap by chance? My wife's gonna hate me by...

Thanks a lot for the quick replies guys. I just finished building my heat exchanger, can't wait to get that PID!! (and SSR, and silicone tubing, and QD's, and...sheesh) Cheers, -Dixon :mug:

I am in the market for a temp controller to be used in a RIMS/HERMS system. I'm going to use a water heater element to heat water surrounding a HERMS coil. I'm wondering what type of controller would best fit my use. I don't know if I need the thing to do math I won't even attempt when I...

I purged the head space and turned the reg down to about 2-4psi and it poured perfectly. Thanks for the advice BierMuncher!

I just sanitized a spoon and tried giving the beer a slow stir to release some carbonation...and WOW! A word to the wise who try this, don't stir too much, The amount of carbonation must be through the roof cause it just about over flowed and made a huge mess. Shoop: I'm using about the same...

Thanks for the quick responses guys!

I just kegged my 1st brew (an ESB) the other day. I let it chill to about 34-36 dergrees and did the 30 psi shake thing for a day. I set the pressure to about 12 psi for the past couple of days to let the carbonation settle and get to where I can drink it soon. I am under the understanding that...

I was wondering what type of cleaning procedures various chillers need. Someone earlier in this thread mentioned back flushing, I have even heard of people storing CFCs with sanitizer in them. I'm curious if you flush them out how you would prevent nastiness from growing in the damp, dark hoses...

Sounds good, thanks for the quick response! -Dixon

I just made a copper sparge arm and tried boiling it in some water for the last hour in an effort to break-up the flux. Unfortunately it didn't work as I had planned. Does anyone have any advice? Thanks! -Dixon

Thanks for the quick responses. I used http //hbd.org/cgi-bin/recipator/recipator and balanced everything out as best as I could. We'll see how it turns out in a couple months. Thanks again! -Dixon

I was planning on brewing the Griffin Spit IPA (extract version) from this months Zymurgy. The recipe calls for a 2 gallon boil. However, I would like to boil all six gallons of water. I was curious what changes need to be made to the boil/hop times and ingredient amounts if any. Thanks for the...

I just cut my kegs open the other day and what helped me out a lot in the deburring (sp?) department was using a sanding wheel. It's also a great way to fine tune that perfect circle without screwing it up, or fixing it if you did screw it up. :cross: You can buy them in 60, 80, and 120 grit...

Ya, I figured that would be the pricey part. I'm going to hit the local hardware store and see how much the 45 degree fittings will be. I just figured I'd ask on here 1st.

We all know how expensive soft copper tubing is. I was wondering what the practicality of using regular copper pipe and various 45 dergree fittings would be? I was looking to make something that would fit in the 12" hole at the top of my Sankey keg and would be tall enough to cool 10 gallon...

I just picked up 3 BG-10 burners with a 0-30 psi adjustable reg. I should be able to run 2 burners at about 105-110k. If for some reason that isn't sufficient I can always reconfigure the schedule 40 with another reg. Thanks for the quick response Lil' Sparky. -Dixon