Search results

Ok, any clone "one" for reference? better a "one" than a wired lolin Mini?

It seems there are no mistakes today. Here you have the video of the result on the display

Ok, It only occurs to me that the probes are bad. Can you think of a way to check this? We wait for the new probe? any other test? I follow the path that you indicate to me. Yes I installed I2C and the LCD works fine.

Hi, I have reinstalled. Good display appearance. I connect the relay, it recognizes it well and it is installed, then I connect the probe to A0 but it is not recognized (I have tested with each of my 3 probes separately) Tell me if you want me to reset the Arduino with the advanced settings...

You can see the configuration in post # 185. the file only has one line with the configuration of my ip. ESP responds to Ping. Today there is nothing new configured.

Hello, Here are the files. It seems that the only recurring message is a problem opening the serial port. 2021-04-12 22:38:12 [E] Starting BrewPi. Error(s) while opening serial port: Could not find compatible serial device.

Hello, It is true that I always start from the same system restoration. If the problem is earlier, we could be working on a problem without knowing it. I have reviewed my procedure prior to starting point. My installation only consists of 1- Linux installation. 2- install xrdp server (sudo...

Hello, after doing the installation with the sequence that you have indicated, I still have problems. I have been capturing all the screens that I have believed appropriate or suggested a question: -Wifi acces point: I answer yes. This point is quite recent. what is it for? - unable to ... I...

Thanck. When I am at home, I will try to do a new installation and test what you tell me in your last post.

Oh my goodness. I'm going to hell for putting you on this path ... Sorry Lee, don't hate me for that ...:eek::eek::eek:

d1 mini only with the power connected. I get the same answer.

Hello, Sure. This shouldn't be so much of a problem. I am sure there is something basic that is wrong and I am checking as ok.

Hello, today I was able to dedicate some time to this. I have reconfigured my wiring, using "protoboard" I have reinstalled brewpiremix as single chambre. I see that the installation asks 2 new questions. I don't know what they mean but I answer "yes" I'm going to configure the config.cfg file...

Hello, just for adding new data. I have prepared one of the new mini d1 purchase batch. The result is the same. On the other hand, I see that now the firmware does not matter and what I install, when I click the button "refresh device list" it never recognizes any of the installed probes. Would...

Ok, I hope, no problem. The only thing I can think of to try to make the job easier is a mini d1 change. I received some I have several purchased at the same time. As I received some damaged I bought some more to replace the damaged one and for future projects. They are still in the unopened...

I only have one SSR connected, but it doesn't install. I have remembered that in the old brewpi I used the command "dmesg" to recognize the serial port (towards this by recommendation, my knowledge does not understand this). I do not know if it helps you, but I have captured the end of that...

ok this is what i have done: - update 0.7.4 - configuration line in config.cfg: port = auto (the old one removed by #) -flashing firmware 0.11 - Serial (sorry, I didn't think to try the old version) - connection between mini d1- Raspberrypi: micro usb-USB - connections on mini D1 pin D-5 --->...

Hi, As for the video, it is a very good idea. My procedure is the same as yours, although it does not work. You mean to flash the devices with firmware rev 0.11 - Serial? I have not tried it. That being the case, I suppose I should connect the device via cable to the raspberrypi, right? What...

No problem, work slowly. I take the opportunity to do other pending issues. Thanks again

I think a thread had come loose. I have left only the 3v8e probe. same result