Search results

If you suspect the bottles to be the problem then after good cleaning where all visible left-over must have gone (else no use) put then in oven prior to bottling at 120´C for 20min, let them cool down slowly, and take them from oven just before you fill them with beer! This way even you did not...

Hi all, I put my review of "Bottling with Sugar cubes and Fermentasaurus (Mini review)!" on my website: www.posebryg.dk

Hi there, did my last 15 brews though Fermentaours, and reused the yeast......I also store in jars, (and further a plastic bag with some alcohol too further limited bacteria growth on the outside part etc.), and I make a 24-hours vitaility starter as I no-chill. Hence, I also just as MrHopScotch...

Hi there and alphaomega, thanks for this project....I know this is not widly beeing updated anymore, then I still look at the "STC1000 OVBC" part. My setup is hot plate, pot and inner-pot with holes for eBIAB like system, and hence using a hot plate to heat and a 220v pump. Question 1, is it...

Hi there, still looking at this project for a brew controller! But as i wish to go headless I would like to know if anyone have tried this, eg. running it without LCD+keypad and buzzer? Second question, can the pump be controlled by pwn, eg. my 40W pump is powerfull and wish to run it at 25%...

Btw......Vito, have you looked at these ones? https://www.itead.cc/wiki/Sonoff_TH_10/16 Using a Tensilica L106, and support 10A and 16A heating for allmost no money! Hence, no LCD nor possible to control pump, but if it is the wish just to control heat and have Wifi control these seems so nice!!

Hi all and especially Vito, super interesting project for my single vessel brewing system (my is based on old table plate stove heater, old brewering pot, magnetic brewing pump and 21L plastic bucket fermenter)! Question, is it correct understod if I buy the "BrewManiacEx BrewShield" I only...

Regarding temperature, Then I have run a few test as I got both Ispindel, the SCT1000 probe and some Weber temperaturmonitors, and I have not yet seen the Ispindel been more than ½-1 degree away from either the 2 other! Hence, I would say in the wort and with a rather good/nearly submerged...

he...he..he.. The sTC1000 give the temperature, and so do the Ispiedel too........! So I was also woundering if you needed the temperature probes and you just controll the frigde/heat from the Ispiedel data? If that would be possible! Thanks!

Hi Pocketmon, thanks for the Work going on here! I have one question though as I am a bit confused (in general), can I put your software on one of Wemos D1 mini I got left from the Ipsidel project and then use BrewPi-less as the monotor data logger from Ispiendel and in that way stop using...

Hi there, also gone the Fermentasaurus way. From reading here I decided to use a hop-sock to filter with, see Picture 1 and 2! Think I gonna use a stainer and some cheesecloth for that next time and just sanitize this by boiling Water! Yeast Collection box emptied after some days...

Hi there, I have used 10 gram (fresh) for 5 min in 18 liter batch, and this give a clear but not overwelming hint of the berriers in a Citra Sea buckthorn wit! Also done a dunkel hefewwisesfen (http://posebryg.bagge-nielsen.dk/2016/10/06/the-funky-dunkel-hefewiezen-with-sea-bucktorn/) with...

Hi there, sorry to hear you visites Carlsberg, as a Dane I find those beer so borrowing unless in is 27`C + (and almost never we get those kind of temps.). Regarding chilling, I just trasfer the still hot wort (80`C +) to my fermenter, and let it chill Down over night with som sanitized liquid...

I just dry hopped the above Red Buhpa, and the tilt changed a bit and it reports G=1016, ofcouse when using around 170grams hops for 18 liter it wil impact........! Just an consideration...!

Hi there, just a picture of the second rund with my alternative Yeast-tube based Ispindel! I have made 3 gravity measument! OG= 1053, where Ispindel said 1056! Mid term Gravity = 1015-16, where Ispindel said 1014. Lastly, Gravity at 1012-1013, where Ispindel said 1013,5. So taking the error on...

To both you, that PCB looks super! Would be perfect in a bit larger and longer version where gryo then is placed just as mine in the cap-head of a yeast tube! Gonna look at Kicad and see if I can make one version just a bit larger and hold 4 copper lines for placing the gyro downwards! Any...

Hi agian, trowed all my data both sugar-solution and 1s run of the fast fermenting US porter of 10L with 10g yeast. Seems it only draws 2nd line?

Tanks, got it working :-)

Btw, Pocketmon, could I get you to repeat it with the following dataset: tilt sg 22,86 1000 24,45 1010 26,79 1014 29,67 1016 31,87 1023 40,49 1026 42,8 1028 41,75 1030 55,91 1040 64,11 1044 65,24 1050 66,18 1064 66,31 1076 Just for the fun :-) Klaus

Thanks, my computer is on the net, so not sure what I do wrong, but mankind always on the hunt for evolution! Anyway it seems to work very fine......and I am exciting to see how second batch will report at the end conta a hydrometer !