Recent content by KellyL

A Little Sumpin' Sumpin

After over two years with no work on this (and a March pump sitting in my garage), I am now able to work on stuff that interests me. Making beer is first on the list (of course). I was traveling at least half of each month from the time I built the stand until now. Anyway, I brewed two...

I'm planning on re-visiting this beer but I'm going to modify the Speckled Heifer recipe a bit to make up for some innefficiencies in my system. Besides these changes I'll follow the instructions from NB. Fermentables: 9lbs 2 row .5 lbs Carapils .25 lbs Flaked Barley .25 lbs...

I had visions of a potential fail today while brewing an extract batch. I was shaking down my stand and saw steam rolling out of the tubes with the open ends. This made me think about the vapor trapped in the welded tubes. I stopped the batch, let it cool a bit and got out the drill. When I...

For a smaller application like yours why can't you use a 5 gallon paint strainer? I have used them for grain in partial mash batches and as hop bags. Just curious, not critiquing. Kelly

The top of the MLT is 82.5" and the shelf is that tall so that it didn't hang over the keggles with no clearance to stir or work comfortably and in case I want to switch to direct fire in the future. It's 61.75" from the ground. It was supposed to be 60" but the casters ended up being a bit...

I just got the burners on mine welded in, I'm sure I'll have some stories but I haven't done a batch on this yet. It still beats lifting kegs full of hot liquid or setting burners on shelving units. I still need a pump to move the water up to the MLT but I'll test it out using pitchers until I...

The burners have never given me a really good blue flame even with nothing on top. They aren't as sooty as some burners but they do leave a bit of crud on the bottom. I'm going to upgrade eventually to either banjos or jets, that's the nice thing about the heavy duty frame. I can grind...

I have finally made progress. Between my son's football season, my college classes, my wife's college classes and my 2 yr old twin girls I haven't had time for anything. I went to Harbor Freight and got the cheap flux core welder to finish this up at my convenience. It only took a few minutes...

We got the stand welded together and most of the welds smoothed out. The casters are uneven and I have to sort that out. His shop floor must have had a huge dip in it right where we were working. I still have to figure out the mounting for the burners and get it painted. I wont be getting any...

We got the steel cut, mocked up and partially welded together today. I changed my mind on the height of the second tier and it's going to give me more room for working in the keggles. Thanks for the suggestion. I still need casters and a way to mount the burners. I'm pretty pleased with...

"Garden hose" should have been outside spigot. I plan on using a potable water hose just in case. FYI, I service aircraft and we fill our potable water trucks out of a sanitized (and inspected monthly) green garden hose. Welding starts tomorrow after my son's 9AM football game.

I just spoke with the welder, told him we'll raise the center up and brace it from the center mast to the edge of the top tier. Then we'll tack sheet metal to it as a heat shield and to allow any condensation a path down (other than in the kettle)

I need the stand to be compact and short, this is why its set up the way it is. I may make the center mast a bit taller, but not much. I'm going to reuse the burners from two turkey fryers for now but may upgrade later. I want to add the filter so I can use my garden hose as a source.

I have a friend that welds and has left over steel. I told him about my idea and he's itching to build. I'll have to buy more steel to complete it but here's my drawing. I don't have a pump but may get one soon if the expenses on this are low enough. I need something compact but cant use a 3...