Recent content by Jerrydfl

I got it to work. On my Raspberry Pi I had the newer Raspian version which is called Buster. I went back to the Stretch version and did not get the Bluetooth error message and was able to set up the Tilt Hydrometer successfully. Jerrydfl

Ok, I did post it on Thursday and got this reply from Terpene..... ---------------------------------------------------------------------------------------------- Try asking in the Fermentrack thread: https://www.homebrewtalk.com/forum/...ewpi-www-replacement-for-raspberry-pi.649303/ I know...

I few days ago I posted to the DIY Project (Fermenters) forum and it was moved yesterday to the Fermentation and Yeast forum. My post was about a problem I was having with my Fermentrack program running a ESP8266 fermentation controller. It was a bluetooth setup issue that has nothing...

Just trying to get my new Tilt Hydrometer set up in Fermentrack and in the Select Sensor Type screen I select "Tilt Hydrometer" and enter in Name, Temp Format and Color and Connection Type "Bluetooth" I then get the following error message... "Connection type Bluetooth packages for python have...

Just trying to get my new Tilt Hydrometer set up in Fermentrack and in the Select Sensor Type screen I select "Tilt Hydrometer" and enter in Name, Temp Format and Color and Connection Type "Bluetooth" I then get the following error message... "Connection type Bluetooth packages for python...

-------------------------------- When I power up the ESP on the phone I see ESP_5574156 as a network... I can connect to it but then it says "Internet may not be available" . I go into the browser and everything is ..." This site can't be reached." I don't see any page come up. ALSO...

I finally got the firmware loaded and everything was running ok. In fermentrack I had my freezer set up at 68 degrees. I have a beer and fridge probe in the freezer and it was running all night ok.. Keeping it at 68. with both heat and cool. However today. it stopped and could not connect...

Ok Thorrak, I started from scratch. I reloaded the raspberry pi again with the current operation system (Strecth). I typed in " curl -L install.fermentrack.com | sudo bash on the pi. After it finished normally I Opened up 192.168.0.2 in my windows chrome browser and got into Fermentrack I...

I am using Fermentrack. I did try to flash the Wiring Test firmware and got same error as soon as I click on "Flash to Device" which is .... "" TypeError at /firmware/flash/6/ _init_() got an unexpected keyword argument 'max_errors' Request Method: POST Request URL...

How can I tell what version of BrewPi I trying t run. Remember I can't run it, as I am not able to connect to the esp8266.

I just installed brewpi on my pi and the flashing to the esp8266 went ok. I get a new wireless network showing up called ESP_08147E , but if I reset the esp8266 that network only shows up for about 1 minute and it goes away. While it is there I am not able to connect to it.. to set the...

I am trying to install Brewpi on my Raspberry pi and when I run sudo ./install.sh I get an error.. Package libapache2-mod-php5 is not available..... some more errors on the end are... E: Package 'php5' has no installation candidate.... I running the new version of raspbian Stretch I gave up...

I have been unable to flash the firmware to my new Esp8266 D1 mini. I can flash a led test program to the esp8266 via the Arduino IDE program and that is ok. I have Fermentrack installed on my pi. Do I have to have Brewpi program flashed to the ESP8266 before I flash the Fermentract. I am...

I am trying to get the Fermentrack up and running. I just applied power to my " Makerfocus D1 Mini NodeMcu 4M Bytes Lua WiFi Development Board Base on ESP8266 ESP-12F N Compatible NodeMcu Arduino (D1 Mini) purchased from Amazon. I am following the GUIDED DEVICE SETUP IN Fermentrack and I get...

I am trying to get the Fermentrack up and running. I just applied power to my " Makerfocus D1 Mini NodeMcu 4M Bytes Lua WiFi Development Board Base on ESP8266 ESP-12F N Compatible NodeMcu Arduino (D1 Mini) purchased from Amazon. I am following the GUIDED DEVICE SETUP IN Fermentrack and I get...