Quantcast

update of depression

HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Help Support Homebrew Talk:

tranceamerica

Well-Known Member
Joined
Jan 22, 2008
Messages
441
Reaction score
2
Location
seattle WA! WA! WA!
Ok...


tonight I racked my first PM batch and it has a HORRID medicine taste - I can only imagine this means a bacterial infection...yuck.

Someone please dear god help me, it looks as if I've killed off two batches in a row.

These are my first PM batches & both are ruined. I can't imagine them ever being drinkable. I'm only keeping them because I can't bear to throw them away yet.

I've never never never made a bad batch of beer until I started this PM thing. all my ME brews have been excellent. What am I doing wrong?!?

Oh, and I tasted the ASSTringent beer again...tonight...and yeah, it's still astringent...maybe a bit less...but maybe I also tasted the medecine taste in it too?!? blah.

what could I possibly be doing different/wrong with the PM batches, versus my ME batches? I"m going to soak all my equipment overnight in sanitizer and for my next batch - it will be ME & I will be very very anal about everything being clean.what else can I do?!?

Then, I need some help figuring out what I'm doing wrong w/PM...before I try it again.

*******************

Ok, for the batch I racked tonight - it had a very watery taste (no malt flavor). I attribute this to the fact that I had to crack the grain myself with my GD rolling pin. and of course, it had the medicine taste too.

The second batch - same recepie - but with properly cracked grain - it seemed to have a bit more mouth feel, but was astringent (too hot on the sparge) and I think it also tasted a bit medeciney. yuk.
 
OP
T

tranceamerica

Well-Known Member
Joined
Jan 22, 2008
Messages
441
Reaction score
2
Location
seattle WA! WA! WA!
note:

I have been reading other threads on nasty medecine tastes. I first assumed that my hoses were the issue, because I haven't changed them in awhile...BUT, neither of these brews were in the hose until tonight when I racked the first one.

So, cross that one off the list

could be bad sanitization procedure. I use bleach - and I do try to rinse it really well.

BUT - for these batches, I didn't worry about too much about sanitizing anything on the hot side of the brew - ie: I didn't worry about my mash tun, big stainless spoon, brew pot...because all that stuff went into the wort and got the heck boiled out of it...right?

Maybe the carboy had some nastys in it?

My procedure is to do the mash, get everything into the brew pot, then add the wort to cold water that's in the carboy & top off with more cold water. The two batches of cold water come straight out of the tap. Then, I cover the lid of the carboy with sanitized tin foil (just to keep crap from falling in it) and put the carboy in the garage overnight to cool...then pitch yeast in the morning.

Please give me some advice. I'm going to get some star-san for one thing.
 

EvilTOJ

Well-Known Member
Joined
Dec 25, 2005
Messages
6,394
Reaction score
64
Location
Portland, OR
It's very frustrating to have several batches go bad or have off flavors. I've been there man. There was a time I had about 6 batches all have a weird off flavor before I figured out what was wrong and it gets so frustrating you just want to give up and go back to buying beer.

My first AG was a pilsner and I ended up getting grain bits in the boil. That beer tasted like tortillas for months, but was drinkable. I certainly learned my lesson!

Now, here's some advice; It sounds like you need some work on your sanitation. Even a tiny bit of bleach smell in the carboy will translate to that bandaid-y goodness. Anything that's been bleached HAS to be rinsed until you don't smell bleach anymore. If you can still smell it, then it's still there. Definitely go with the star-san. Also, throw out your tubing and buy new tubing. Seriously. It's cheap and easy to do.

For your sparging, you can keep using the vegetable steamer, as long as you put the grain in a grainbag first. That'll keep it from escaping. 180º sparge water is fine. I typically dump 180º to 190º sparge water into my batches to get the sugars nice and dissolved. The mash temp rarely gets above 175º that way.

Also, it's not recommended to let the wort sit with unpitched yeast overnight. That's the most likely time of getting contamination from wild yeasts and bacteria, so that's just asking for trouble. At least use an ice bath, and boil and cool your top up water for now until you get your sanitation woes under control.

And don't dump them yet! Off flavors have a way of mellowing out and disappearing as the beer ages. The taste of beer as you rack is normally very watery tasting, so that has nothing to do with your crush.

That's all I can think to type for now, I'll probably add more later.
 

TexLaw

Here's Lookin' Atcha!
Lifetime Supporter
Joined
Sep 19, 2007
Messages
3,673
Reaction score
36
Location
Houston, Texas
I agree that you ought to switch sanitizers. That medicinal smell and taste can come from chlorophenols, which can result from leaving even just the tiniest bit of bleach behind. They also can come from the chlorine in that tap water that you add, so look into bottled water or treat your water to remove chlorine. Those chlorophenols have a very low perception threshhold, too, so a little goes a long way.

The medicinal notes also can come from a wild yeast infection, rather than bacteria. Bacterial infections will sour a beer. To avoid those infections, you really ought to cool your beer and pitch as soon as you can. Look into a wort chiller or use some boiled, chilled water to get your temperature down more quickly.


TL
 
OP
T

tranceamerica

Well-Known Member
Joined
Jan 22, 2008
Messages
441
Reaction score
2
Location
seattle WA! WA! WA!
thanks much for the advice guys. Here's my idea for the next batch, tell me if I'm missing anything:

1) do a malt extract batch, just to keep it simple this time
2) rinse the heck out of everything
3) heck, boil some of the stuff, if it will take it
4) get star san
5) replace rubber bits - stoppers and hoses
6) preboil top off water, cool it (I'm thinking that I boil 4 gallons the night before, let it cool in the brew pot, then pour it into a second carboy to store until brew time?)
7) get a big plastic bucket for sanitizing in - I've been using one bowl of my sink, but not sure it's really big enough. Can I use a home depot type bucket, or do I need to invest in a more official brewing bucket? It's just for sanitizing.
8) replace my funnel, it may have some scratches in it.
9) get a wort chiller - or at least do the ice bath (note that "overnight" usually means just a few hours - I finish brewing about 2 am...then up at 7 to pitch)

yeah, the yeast coming out of the batch I racked last night had a horrid smell, really really bad. I guess I'll bottle this batch, but I can't imagine how it'd be good in time.
 

discgolfin

Well-Known Member
Joined
Jul 3, 2007
Messages
615
Reaction score
5
Location
Chicago, Il.
Bleach is what I would bet the house on. Look into your water profile and get star san..This stuff rocks..It hands down has made my brewing easier and better than just about anything. I think getting rid of tubing will help eliminate that this could be wild yeast but it sounds like you didnt rinse the bleach well. Dont rinse after star san..it will have tons of bubbles but believe me it will not affect the beer one bit..dont fear the foam..This stuff is a bit more pricy than bleach but than again dumping 10 gallons of brew is as well.:(

Jay
 

Finn

Well-Known Member
Joined
Jul 21, 2007
Messages
202
Reaction score
1
Location
Albany, Oregon
It sounds to me more like a wild yeast issue than an infection, too. But, well, there are several things to suspect here:

1. Bad tap water. Chloramine in city water can be a problem; low-risk (but bad-tasting) pathogens in country water, likewise. To control for this, you can boil your top=off water the night before, like you said -- another idea is to get some quart Mason jars and lids and fill them with water, put them in your kettle (as many as will fit) and fill it up with water and boil it for 10 minutes. This will give you a gallon or two of sanitized topping-off water, hermetically sealed in quart jars, and another couple gallons of sanitized rinsing-off water. You don't want to be sanitizing with bleach and then rinsing the bleach off with unsanitized tap water.

2. Wild yeast. With the carboy open and no yeast pitched, you're kinda ripe for this, I'm thinking. Especially if you're putting it up in a place where fruit is stored. Grapes and apples are lousy with wild yeast. It could get into your carboy with the natural draft that occurs when a vessel of hot stuff cools down -- it sucks air in as it does so -- which is how Mason jars seal. I'd press the bathtub into service for this, or at least the kitchen sink -- set your kettle in an ice bath. (I'm lucky in that my sink drains across the middle, so I just set the kettle in there and run water continuously into it, letting it drain to the other basin. If yours is the same, you can do that and save money on ice.) You can also boil some water, cool it in the kettle with the lid on, pour it into sanitized Tupperware filling it three-quarters full, and freeze it (with the lid on), to be dropped directly into your wort.

The important thing is to give the yeast you pitch a massive competitive advantage on any stray spores that land in the wort, instead of the other way round, as can be the case if they get into warm wort with a few hours' head start. Also, make a starter and pitch big! 24 hours in a sanitized Mason jar in previously-boiled 1.030 wort will give you a yeast colony capable of totally dominating almost anything.

3. Aluminum. If your brewpot is aluminum, or if you're mashing in an aluminum tun, depending on what your pH level is you could be getting metals off your pot.

I wouldn't bother replacing your rubber stuff. Boil it. It'll be fine.
 

conpewter

Well-Known Member
Joined
Nov 2, 2007
Messages
5,085
Reaction score
57
Location
East Dundee, Illinois
My thoughts on:

6) preboil top off water, cool it (I'm thinking that I boil 4 gallons the night before, let it cool in the brew pot, then pour it into a second carboy to store until brew time?)

I would look into campden tabs( sodium or potassium metabisulfite) to get rid of chloramines. Chlorine is removed from tap water by boiling but I don't believe that Chloramines are. Or to be extra safe this next batch use bottled water (@ 50 cents a gallon it's not a huge expense)
https://www.homebrewtalk.com/showthread.php?t=41018&page=1

7) get a big plastic bucket for sanitizing in - I've been using one bowl of my sink, but not sure it's really big enough. Can I use a home depot type bucket, or do I need to invest in a more official brewing bucket? It's just for sanitizing.

A bucket form Lowes or HD will be fine for sanatizing

8) replace my funnel, it may have some scratches in it.
Good idea

9) get a wort chiller - or at least do the ice bath (note that "overnight" usually means just a few hours - I finish brewing about 2 am...then up at 7 to pitch)

For full boils you really need a wort chiller, for a partial one its not too hard to use an ice bath, both are better than letting it sit around. Also do make sure to make a starter to give your yeast a head start.
 

malkore

Well-Known Member
Joined
Jun 15, 2007
Messages
6,924
Reaction score
50
Location
Nebraska
one-step works, but its not as economical as Star San, and you MUST make sure it dissolves fully, or it can leave residue that can make the beer taste funny.

one-step needs several minutes of contact time to work, and will only stay active a few days. star san works in 30 seconds, lasts for weeks/months...and will not give the beer any funny tastes if you have some residue.

it would be worth ordering star san online if you have to. the big bottle is like $14 at Willaims brewing and makes a few hundred gallons of sanitizing solution.
 

Homebrewjosh

Active Member
Joined
Apr 10, 2007
Messages
31
Reaction score
0
Location
Janesville, WI
I'd have to agree too that Star San rocks. Just dont be afraid of the foam. When I started using it. I took allot of self control NOT to rinse to form away. But the form gets in the micro scratches are cracks to clean. Don' t feel bad. about our batching going south. Its all part of brewing.

Good luck with your future batches
 

Scotty_g

Well-Known Member
Lifetime Supporter
Joined
Mar 26, 2007
Messages
360
Reaction score
14
Location
De Pere, WI
One other solution I'll throw out for your water problem is to get bottled spring water. My tap water recently changed and it has a little more chlorine in it; I don't know how much, because I've never risked it in beer.

I use spring water from the grocery store (in 1-gal sealed jugs) for everything that touches malt. I top off with freshly-sealed jugs after I wash down the lids with one-step. When I end up with partial jugs, I save them for the next boil after marking them as "unclean". (The risk of this is that people may think your brew room has leprosy.)

I second the suggestion of getting at least an immersion cooler, too. After we ran out of ice (brewpartner just grabbed a couple bags instead of letting me calculate it out) and had to use snow, we decided it would be $40 well spent. The immersion cooler means we have the lid on the pail in about 30 minutes after flame out, give or take.
 
OP
T

tranceamerica

Well-Known Member
Joined
Jan 22, 2008
Messages
441
Reaction score
2
Location
seattle WA! WA! WA!
ok...i need some straight answers on a couple of other things...

1) is there any hope for this beer, or should I dump it? I feel so bad about it, I mostly just want it gone from my life. I can STILL smell it....yuck!!! even though I've cleaned up. it's just stuck in my brain...

2) I boiled all my brewing stuff...but my hoses turned white!!! are they ruined? on a happy note, it seemed that I got a lot of crap off the stuff - the water turned yellow - probably from boiling the grain bags mostly...
 

Finn

Well-Known Member
Joined
Jul 21, 2007
Messages
202
Reaction score
1
Location
Albany, Oregon
tranceamerica said:
ok...i need some straight answers on a couple of other things...

1) is there any hope for this beer, or should I dump it? I feel so bad about it, I mostly just want it gone from my life. I can STILL smell it....yuck!!! even though I've cleaned up. it's just stuck in my brain...

2) I boiled all my brewing stuff...but my hoses turned white!!! are they ruined? on a happy note, it seemed that I got a lot of crap off the stuff - the water turned yellow - probably from boiling the grain bags mostly...
Unless you desperately need the carboys empty for your next batch, I'd stash 'em in a cool place (60 degrees or so) and leave 'em for a month. Or as long as you can before you need the glass they're in. Miracles do happen and you'd be surprised some of the nasty flavors yeast will pull out of the beer over time. Man, you should have tasted my dry stout two days into fermentation ...!

Don't worry about the white hoses either. Mine are like that too. I should mention, though, I ruined a bottling wand boiling it -- it curved to match the shape of the pot.
 
OP
T

tranceamerica

Well-Known Member
Joined
Jan 22, 2008
Messages
441
Reaction score
2
Location
seattle WA! WA! WA!
thanks for the advice - I think I'll bite the bullet and bottle the batch & leave it for a month before trying it - do you think this will be as good as leaving it in the carboy? Probably....I'll leave the tip off the bottling wand to get as much yeast in as I can (I've already racked it...) I need the carboy soon, because I want to get a decent batch brewed.

I think I'll go ahead and replace the hoses anyway - they've been around too long as it is.

here's to yeast !!! and my prayer for these two batches...
 
Top