Hi All,
Getting out of homebrewing trying to lower my cholesterol and weight and have more time with my kids. Local pickup only.
SOLD - 2 tap keezer $400
insulated, 7 cf, can accommodate 4 cornys as far as I planned...just never got around to adding the two additional taps.
Intertap, flow control and regular tap with self closing spring. drip tray, EVA barrier and duotight for lines and gas. I will include my 5 lb CO2 tank and a 5 gal and 2.5 gal keg if u do the full asking price. The kegs were purchased new from AIH, and the co2 tank is a "swap", mostly full. I can include my tap-rite reg, and it works, but the screw on the dials is rusted a bit... I have a 2 split gas manifold that I never got around to mounting, but will include all the fittings to install. Has a Johnson 1-stage temp controller mounted. PM me with anything I forgot to mention.
SOLD - Ferm chamber, $220
7 cf chest freezer, inkbird temp Ctrl. Low watt density heating mat, ran line inside to do stir plate, will include stir plate and 4L flask if u do the full asking price. Plenty of slack on temp sensor so you can tape to side of your fermenter for getting reading on wort temp.
SOLD - Boil Kettle - $180
All stainless. Two ball valves to control recirculation, temperature measurement with dial gauge. Whirlpool tube, diptube. 8.5 gal. marking stamped into pot. Hop spider included. PM me with any questions.
Mash tun - $240
Still available...but chiller coil/HERMS coil is sold.
custom made. All stainless with flexible dip tube using high grade silicone and oetiker clamps. False bottom is NorCal brewing made, custom, sits under dip tube for better efficiency with smaller batches. dial thermometer currently, but easy to upgrade to RTD sensor. Uses loc-line to recirc. Works very well. Not planning to include stainless chiller in either boil kettle or mash tun sale, but if you do want that, it's how I did kind of a HERMS setup and also could use it for chilling, would include it for an additional $60.
All fittings are Ball-lock quick disconnect. Most of the fittings in this build I bought from brew-hardware.com
I also have a bunch of other stuff that I'll post in the coming weeks, so if you live in San Diego, PM me and we can chat about what I have.
Getting out of homebrewing trying to lower my cholesterol and weight and have more time with my kids. Local pickup only.
SOLD - 2 tap keezer $400
insulated, 7 cf, can accommodate 4 cornys as far as I planned...just never got around to adding the two additional taps.
Intertap, flow control and regular tap with self closing spring. drip tray, EVA barrier and duotight for lines and gas. I will include my 5 lb CO2 tank and a 5 gal and 2.5 gal keg if u do the full asking price. The kegs were purchased new from AIH, and the co2 tank is a "swap", mostly full. I can include my tap-rite reg, and it works, but the screw on the dials is rusted a bit... I have a 2 split gas manifold that I never got around to mounting, but will include all the fittings to install. Has a Johnson 1-stage temp controller mounted. PM me with anything I forgot to mention.
SOLD - Ferm chamber, $220
7 cf chest freezer, inkbird temp Ctrl. Low watt density heating mat, ran line inside to do stir plate, will include stir plate and 4L flask if u do the full asking price. Plenty of slack on temp sensor so you can tape to side of your fermenter for getting reading on wort temp.
SOLD - Boil Kettle - $180
All stainless. Two ball valves to control recirculation, temperature measurement with dial gauge. Whirlpool tube, diptube. 8.5 gal. marking stamped into pot. Hop spider included. PM me with any questions.
Mash tun - $240
Still available...but chiller coil/HERMS coil is sold.
custom made. All stainless with flexible dip tube using high grade silicone and oetiker clamps. False bottom is NorCal brewing made, custom, sits under dip tube for better efficiency with smaller batches. dial thermometer currently, but easy to upgrade to RTD sensor. Uses loc-line to recirc. Works very well. Not planning to include stainless chiller in either boil kettle or mash tun sale, but if you do want that, it's how I did kind of a HERMS setup and also could use it for chilling, would include it for an additional $60.
All fittings are Ball-lock quick disconnect. Most of the fittings in this build I bought from brew-hardware.com
I also have a bunch of other stuff that I'll post in the coming weeks, so if you live in San Diego, PM me and we can chat about what I have.
Attachments
Last edited:
