Quantcast

Contaminated??

HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Help Support Homebrew Talk:

bc23

Active Member
Joined
Jan 13, 2008
Messages
29
Reaction score
0
Location
New York
I've bottled my first batch (Brewer's Best Irish Stout) now, but during the brew I'm afraid that I did some things that were not as sanitary as they should have been.

My question is, how do I know if it was contaminated??

Thanks for any help
 

budbo

Beer is good
Lifetime Supporter
Joined
Feb 6, 2006
Messages
2,294
Reaction score
21
Location
La Plata, MD
bc23 said:
I've bottled my first batch (Brewer's Best Irish Stout) now, but during the brew I'm afraid that I did some things that were not as sanitary as they should have been.

My question is, how do I know if it was contaminated??
If you contaminated it prior to fermenting things to look for at bottling would be foul smelling floaties with a hairy texture, a general foul smell etc.

In the Bottles, Your first clue will be floating or clumpy sediment instead of normal bottom sediment. The second would be nasty smell when you pop one, the third would be spraying the first taste accross the room and running for something to rinse your mouth with (or it could just be a grimace and spit).

Relax :mug: Homebrew is forgiving, especially at bottling time since it has limited fermentable sugars left and alcohol content. And if you had contaminated it prior to bottling you'd probably know it already

What exactly did you do that was unsanitary?
 
OP
bc23

bc23

Active Member
Joined
Jan 13, 2008
Messages
29
Reaction score
0
Location
New York
budbo said:
If you contaminated it prior to fermenting things to look for at bottling would be foul smelling floaties with a hairy texture, a general foul smell etc.

In the Bottles, Your first clue will be floating or clumpy sediment instead of normal bottom sediment. The second would be nasty smell when you pop one, the third would be spraying the first taste accross the room and running for something to rinse your mouth with (or it could just be a grimace and spit).

Relax :mug: Homebrew is forgiving, especially at bottling time since it has limited fermentable sugars left and alcohol content. And if you had contaminated it prior to bottling you'd probably know it already

What exactly did you do that was unsanitary?
Ok great - thanks - The brew tastes/smells great, and I'm happy with it.

How did I potentially contaminate?....I almost don't want to say as it's so dumb

I don't have a chiller, so when I was trying to cool down the wort I had it sitting outside in the fermenter inside of a big plastic bucket. I put snow all around the fermenter, but some of it got in the wort - DUMB. Then, to make matters worse, when I was trying to get the temperature of the wort, I used an electric meat thermometer which I completely forgot to sanitize. Also DUMB.

But, I guess I dodged a bullet (or 2), as the beer tastes and smells great!
 

Alabama Brewer

Well-Known Member
Joined
Jan 16, 2008
Messages
47
Reaction score
0
Location
Birmingham
Another dead give-away................look at the neck of your bottles. If you see a foamy ring around the top level of the brew, that is cause for concern. Also, if you crack one open and it overflows like a volcano, it's all over.

I generally breath easy after bottling if I inspect the bottled brew for signs of a ring and don't see one.
Cheers :mug:
 

EvilTOJ

Well-Known Member
Joined
Dec 25, 2005
Messages
6,394
Reaction score
64
Location
Portland, OR
bc23, those aren't dumb mistakes. It happens sometimes, but rarely something to be that concerned about. You'll find as you make more batches that it's actually rather difficult to contaminate a batch. Just the same, do not slack on your sanitizing procedures! The only time I had to dump a batch was when I'd forgotten to clean out a carboy for clearing and aging. Nasty stuff started growing on top.
 

Yooper

Ale's What Cures You!
Staff member
Admin
Mod
Lifetime Supporter
Joined
Jun 4, 2006
Messages
74,468
Reaction score
12,092
Location
UP/Snowbird in Florida
They all gave good advice- practice good sanitation, but don't worry if things happen. If something is contaminated, it really becomes very obvious. I've made a ton of beer and wine in the last two years, and just had my first dumper batch. I kind of suspected it all along because it just wasn't "right" from the starter on to the finish, but I waited it out. Sure enough, it was obvious that it was infected.

So, don't worry- it's much harder to screw up than you'd think!
 

Bobby_M

Vendor and Brewer
HBT Sponsor
Joined
Aug 3, 2006
Messages
24,829
Reaction score
3,503
Location
Whitehouse Station
Next time chill in the brewpot, not the bucket. You shouldn't be pouring hot wort into a bucket anyway. At the very least but a cover on to keep wild yeast out.
 

libs

Well-Known Member
Joined
Apr 24, 2007
Messages
100
Reaction score
0
Location
Livonia, MI
It's definatlly contaminated.....once it's done, bottle it and PM me so I can give you an address to send it to so I can dispose of it for you. Just trying to help.
 

EamusCatuli

Well-Known Member
Joined
Jan 21, 2008
Messages
531
Reaction score
1
Location
Chicago
Im pretty sure the first batch of brew I made *a whole month ago!*, I thought that I 100% surely contaminated it because some old nasty caulk from my sink made it into the wert before I sealed it in the primary. The beer is fine and I have already enjoyed a few brews with my friends. No worries!

Cheers :mug:
 

reshp1

Well-Known Member
Joined
Dec 13, 2007
Messages
161
Reaction score
1
Bobby_M said:
Next time chill in the brewpot, not the bucket. You shouldn't be pouring hot wort into a bucket anyway. At the very least but a cover on to keep wild yeast out.
Yup, the plastic is a surpisingly good insulator, it takes forever to chill. Next time, try bringing in enough snow to fill your sink, then add a bit of water to make a stiff slush. The water makes better contact with the metal brew pot, which will conduct the heat out much much faster.
Stir the slush and the wort occasionally to cool even faster
 

Jumbo82

Well-Known Member
Joined
Dec 27, 2007
Messages
499
Reaction score
4
Location
Plymouth
Bobby_M said:
Next time chill in the brewpot, not the bucket. You shouldn't be pouring hot wort into a bucket anyway. At the very least but a cover on to keep wild yeast out.
For my last few batches I have taken my brewpot and set it on the back porch on snow to chill. Within an hour its down to temperature. I haven't put a cover on it because I figured that would slow down the cooling process and I didn't think there would be much wild yeast in the air on a cold winter day. So far no contamination, but in the future should I put a cover on my brewpot? How much wild yeast is flying around outside in the winter? I thought it would be more likely to get infected from airborne bacteria inside since we have a cat, dog, etc.
 
Top