**Updated as equipment is sold - check post replies for updates**
The original post has been broken up since equipment has been sold off in groups and pieces. Current list below as of 3/12/23:
Brew Controller
Custom built based on The Electric Brewery controller. All items sourced from Auber Instruments. Built in breaker protection. This panel requires a 30 amp GFCI breaker and the proper wiring and outlet to operate (all available for an additional cost, you might need to source your own wire depending on length). You can run either kettle individually as controlled by the center element selector switch. Switched outlets for both the HLT and wort pumps. PID controllers for the HLT and mash temperatures for precise control along with a digital SSR regulator to give more control over the boil adjustments.
ASKING: $525
HLT
20 gallon electric HLT with HERMS coil, fill valve and very efficient dip tube to empty 99% of the water volume. Built in temp probe and supplied cable to plug into the brew controller for precise temperature control.
ASKING: $425
Mash Tun
20 gallon mash tun with custom Jaybird false bottom and sparge/recirculation valve for integration with HERMS coil in HLT and built in temp probe and supplied cable to plug into the brew controller for precise temperature control.
ASKING: $250
Boil Kettle
15 gallon electric boil kettle with hop stopper stainless mesh hop/trub filter.
ASKING: $300
Complete Brew System: 3 Vessels + Controller
COST: $1,900 (OR $2,190 W/TWO CHUGGER PUMPS)
ASKING: $1,500 (OR $1,700 W/TWO CHUGGER PUMPS)
Keezer/Kegerator
Currently setup with 4 taps for 4 serving kegs. Has room for up to (8) 5 gallon kegs and 8 taps. You can add on to the existing secondary regulator inside, a 3-valve gas extender is listed below but not installed. The external tank regulator is setup with one line into the keezer for serving kegs and a second utility line for transferring beer, etc. All stainless Perlick taps along with push to connect fittings for ease of maintenance and replacement of beer lines.
ASKING: $600
Misc Equipment
Tons of brewing equipment, supplies and accessories for all of the various phases of the brewing process.
ASKING TOTAL: $1,195
ASKING PRICES
Most are 1/2 of what I paid, some even less. The more items purchased at once the better the deal.
Located in Bethel, CT
The original post has been broken up since equipment has been sold off in groups and pieces. Current list below as of 3/12/23:
Brew Controller
Custom built based on The Electric Brewery controller. All items sourced from Auber Instruments. Built in breaker protection. This panel requires a 30 amp GFCI breaker and the proper wiring and outlet to operate (all available for an additional cost, you might need to source your own wire depending on length). You can run either kettle individually as controlled by the center element selector switch. Switched outlets for both the HLT and wort pumps. PID controllers for the HLT and mash temperatures for precise control along with a digital SSR regulator to give more control over the boil adjustments.
- Enclosure: $130
- Panel tags: $40
- Breakers: $20
- Instruments: $300
- 30 amp relays: $75
- 30 amp L630R outlets: $25
- 15 amp single outlets: $10
- Power cord, wire, terminals, zip ties & mounts: $30
ASKING: $525
HLT
20 gallon electric HLT with HERMS coil, fill valve and very efficient dip tube to empty 99% of the water volume. Built in temp probe and supplied cable to plug into the brew controller for precise temperature control.
- 20 gal Concord kettle (80 QT): $100
- Blichmann 20 gal BoilCoil electric heating element: $175
- HERMS coil, compression fittings, valves and quick connects: $165
- Main valve, tee, dip tube & fittings: $30
- Temp probe & cable: $45
- Fill valve & fittings: $20
- Site glass: $20
ASKING: $425
Mash Tun
20 gallon mash tun with custom Jaybird false bottom and sparge/recirculation valve for integration with HERMS coil in HLT and built in temp probe and supplied cable to plug into the brew controller for precise temperature control.
- 20 gal Concord kettle (80 QT): $100
- Jaybird false bottom: $115
- Main valve, tee, dip tube & fittings: $30
- Temp probe & cable: $45
- Sparge/recirc valve & fittings: $20
- Site glass: $20
ASKING: $250
Boil Kettle
15 gallon electric boil kettle with hop stopper stainless mesh hop/trub filter.
- 15 gal Concord kettle (60 QT): $90
- Blichmann 15 gal BoilCoil electric heating element: $160
- Hop Stopper: $65
- Main valve & fittings: $25
- Thermometer & fittings: $25
- Site glass: $20
ASKING: $300
Complete Brew System: 3 Vessels + Controller
COST: $1,900 (OR $2,190 W/TWO CHUGGER PUMPS)
ASKING: $1,500 (OR $1,700 W/TWO CHUGGER PUMPS)
Keezer/Kegerator
Currently setup with 4 taps for 4 serving kegs. Has room for up to (8) 5 gallon kegs and 8 taps. You can add on to the existing secondary regulator inside, a 3-valve gas extender is listed below but not installed. The external tank regulator is setup with one line into the keezer for serving kegs and a second utility line for transferring beer, etc. All stainless Perlick taps along with push to connect fittings for ease of maintenance and replacement of beer lines.
- GE 10 cu.ft. chest freezer: $320
- Perlick taps, hardware, fittings & lines: $530
- Regulator: $95
- 3 valve gas extension: $75
- Cedar collar: $60
- Johnson Temp Controller: $65
ASKING: $600
Misc Equipment
Tons of brewing equipment, supplies and accessories for all of the various phases of the brewing process.
- Jaded CFC (counter flow chiller): $180 (Asking: $100)
- Chugger pumps: $145 x 2 = $290 (Asking: $100/ea x2 = $200)
- 50’ stainless wort chiller: $80 (Asking: $50)
- Mark II Keg & Carboy Washer: $75 (Asking: $50)
- Brew Tapper refractometer: $30 (Asking: $15)
- Hanna Instruments HI98128 pH meter & solutions: $80 (Asking: $50)
- StirStarter Yeast Plate: $45 x2 = $90 (Asking: $30/ea x2 = $60)
- 2000mL flasks: $20 x 2 = $40 (Asking: $10/ea x2 = $20)
- 36” stainless mash paddle: $40 (Asking: $20)
- Monster Mill MM-2 grain mill: $200 (Asking: $150)
- (1) SS Brew Bucket 7 gal w/ 3” TC domed lid: $200 + $75 = $275 (Asking: $200)
- (1) SS Brew Bucket Brewmaster Edition 7 gal w/ 3” TC domed lid: $230 + $75 = $305 (Asking: $230)
- (2) 6.5 gallon calibrated carboy: $50 x 2 = $100 (Asking: $30/ea OR 2 for $50)
ASKING TOTAL: $1,195
ASKING PRICES
Most are 1/2 of what I paid, some even less. The more items purchased at once the better the deal.
Located in Bethel, CT
Attachments
Last edited:
