Australian Pale Ale

Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum

Help Support Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

FlyingWombat

Member
Joined
Jun 7, 2022
Messages
20
Reaction score
18
Location
Australia
Flying Wombat Australian Pale Ale – All-Grain Recipe



PDF is attached but here's one to the cloud version!

Batch size & ABV

  • 38L (2 19L corny kegs) / 10 gal finished beer
  • 50L (13.2 gal) wort
    • For a smaller 19L (5 gal) batch size simply half the ingredients of this recipe
  • Starting gravity – 1.054
  • Final gravity 1.01
  • ABV – 5.7%

Water

  • With sparging
  • 30L (7.9 gal) strike water approx. 73°C (163°F) use this calculator to determine your strike water starting temp for a 66°C (151°F) mash Calculators — Chase The Craft
  • 35L (9.2 gal) sparge water at 78°C (172°F)
  • Without sparging
  • 60L (7.9 gal) strike water approx. 69°C (156°F) use this calculator to determine your strike water starting temp for a 66°C (151°F) mash Calculators — Chase The Craft
Malts:

  • Pale ale malt – 9.6kg (21.16 lb)
  • Medium Crystal Malt – 400g (14.1 oz)

Hops & whirlfloc tablets

  • Galaxy
    • 8g (0.3 oz) - 60 minutes left in the boil
    • 60g (2.1 oz) – whirlpool for 20 minutes at 75°C (167°F)
    • 60g (2.1 oz) - Dry hop at gravity 1.013 (approx. day 6-10 depending on your yeast)
  • El Dorado
    • 60g (2.1 oz) – whirlpool for 20 minutes at 75°C (167°F)
    • 60g (2.1 oz) - Dry hop at gravity 1.013 (approx. day 6-10 depending on your yeast)
  • Azacca
    • 60g (2.1 oz) – whirlpool for 20 minutes at 75°C (167°F)
    • 60g (2.1 oz) - Dry hop at gravity 1.013 (approx. day 6-10 depending on your yeast)
  • Whirlfloc tablets
    • 2.5 tablets – 15 minutes left in the boil
Yeast options & fermentation temperatures

  • 23g (0.8 oz) Kveik (we used a Framgarden strain but any kveik is great!) ferment at 34°C
  • 23g (0.8 oz) US-05 – ferment at 20°C
  • 23g (0.8 oz) S-04 – ferment at 19°C

Step 1 – Milling

  • Mill grains to medium crush (set mill rollers to a gap of approx. 1mm / 0.039 inches)
  • Just keep in mind roller gap settings are not universal so as you brew more batches you will find the ideal crush size for your setup
  • Alternatively if you don’t have a grain mill you can order your grains crushed from most homebrew stores, both online and in person
Step 2 – Mashing

  • Mash for 60 minutes at 66 °C (151°F)
    • Set your strike water to a few degrees above the target mash temperature, you can use this calculator to determine what your strike temperature should be Calculators — Chase The Craft
  • ensure you mix in the grains thoroughly with a mash paddle to prevent dough balls from forming (big spoons, spatulas or whisks will also work)
    • its easier to mash the grains and prevent dough balls if you add a little grain at a time, mix, add more grain and repeat until all the grains are mixed
  • if you don’t have a mash tun with heating then ensure after you have finished mixing the grains in to insulate your mash tun (thick neoprene or heavy blankets both work well)
Step 3 (optional) – Sparging

  • if your setup has the capability to sparge then do so with 35L (9.2 gal) of sparge water at 78 °C (172°F)
  • if you are not sparging and using a BIAB (brew in a bag) method then remove grains from mash tun and twist and squeeze the bag to get as much liquid out of the grains as possible
  • as you start sparging (or straining your BIAB bag) begin raising the temperature of your wort to a boil
Step 4 – Boiling

  • once your wort begins to boil start a timer for a 60-minute boil and add your bittering hops, 8g (0.3 oz) of Galaxy
  • at 15 minutes left in the boil add 2.5 whirlfloc tablets
  • after 60 minutes of boiling turn of the heat and chill the temperature of the wort down to 75°C (167°F) and begin whirlpooling
    • if you don’t have a wort chiller you could rest your boil kettle in an ice bucket
    • if your system can’t whirlpool you can also achieve this with a mash paddle and a power drill, if you don’t have this either don’t worry about whirlpooling it’s not completely necessary
Step 5 – Whirlpooling / whirlpool hop additions

  • once the temperature reaches 75°C (167°F) and you have started whirlpooling add your whirlpool hops, 60g (2.1 oz) each of Galaxy, El Dorado and Azacca
  • allow hops to whirlpool in the wort for 20 minutes and then begin chilling wort again down to yeast pitching temperature
  • once you’ve reached yeast pitching temperature take an original gravity reading of your wort
Step 6 – Yeast Pitching

  • It is best to make a yeast starter before beginning your brewday (ideally 1 day before) to ensure your yeast are as active and healthy as possible before pitching, but not completely necessary – you could also just rehydrate yeast 30 minutes before pitching.
  • Pitch yeast in wort a degree or two higher than the target fermentation temperature to help yeast take off more aggressively
    • To make a yeast starter do this you can use either:
      • DME (dry malt extract) at a ratio of approx. 100g per 1L water (3.5 oz per 33 fluid ounces) for a gravity of approx. 1.040
      • some unfermented wort kept cold and sanitary from a previous brewday
      • 70g of table sugar per 1L water (2.5 oz per 33 fluid ounces) – however it is best to use malt sugar (wort / DME) whenever possible to reduce the chance of shocking the yeast with a different food source from starter to wort pitching
    • To rehydrate yeast
      • Add yeast to approx. 10 times as much room temperature water as the weight of the yeast e.g. 10g yeast in 100 ml water (0.35 oz yeast in 3.5 fluid ounces water)
Step 7 – Fermentation & dry hopping

  • Allow yeast to ferment over the next week to two weeks
  • If you have a temperature controlled system keep the fermenter temperature to the recommended fermentation temperature for each yeast strain (stated in the yeast ingredients section above)
  • Monitor the fermentation activity over the first 7 days by the bubbling of the blow off tube / airlock of your fermenter, as the bubbling slows down (roughly around day 7) take a gravity reading. When the gravity reaches around 1.014 raise the temperature of your fermenter by 1-2 degrees for 2 days for a diacetyl rest (if you don’t have temperature control don’t worry about this step, its not the end of the world!)
    • Its important to note that fermentation times will vary based on your circumstances like, temperature, amount of yeast pitched, healthiness of yeast, gravity of wort, pH etc. so don’t stress be patient and know that these times are just a rough guide
  • On day 2 of the diacetly rest (once gravity reaches roughly 1.012 – 1.014) add 60g (2.1 oz) each of Galaxy, El Dorado and Azacca to your fermenter
  • One day after dry hopping take a gravity reading, fermentation should finish at about 1.010, if you haven't reached this yet wait another day and take another reading, once the gravity is the same 2 days in a row move on to cold crashing! (If you can’t / don’t want to cold crash go straight to kegging/bottling your beer!)

Step 8 (optional) – Cold crashing

  • begin cold crashing your fermenter (bring the temperature of your fermenter down to as close to 0°C (32°F) as possible, for 2 days to a week depending on how patient you are
  • If you don’t have a temp controlled fermenter, you can cold crash by putting your fermenter in a fridge or temp controlled chest freezer
  • After you have finished cold crashing its time to keg/bottle your beer! If you are bottling your beer from the fermenter uncarbonated remember to add about 5-7 grams (0.17 - 0.24 oz) of priming sugar to your bottles to carbonate your beer.

Check out our socials:

YouTube: https://www.youtube.com/channel/UCtU3A9gdOk7IVIKtcRy9Hvw

Instagram: Login • Instagram

Facebook: Flying Wombat Brewery

Twitter: https://twitter.com/FW_Brewery

TikTok: TikTok



Cheers!
 

Attachments

  • Aussie-Pale-Ale-All-Grain-Recipe-21-6-22.docx (3).pdf
    418.3 KB
Last edited:
Back
Top