Search results

Just a heads up EVERYONE on what I ran across with Monster Mills now being made in China. http://zjautomax.en.made-in-china.com/product/yoKQOeMGlChx/China-Barley-Crusher-Malt-Mill-2.html Enlarge the mill side plates, surprise! I bet the MM3-2.0 is also made in China to. A couple years...

I ran across this complete Syncrowave 250 on ebay it comes complete with Watermate 1 cooler, wet torch with gas flow meter with the HD foot control. Only thing missing add your own bottle, 6 days left $750 starting bid. Just a heads up anyone, Prost. Carl...

Had to forward this for those that clean soft items, cast zinc, pot metal, aluminum, brass or copper to like new without damage. Just wash and dry after. http://www.aircooledtech.com/tools-on-the-cheap/soda_blaster/

http://www.amazon.com/dp/B001BMGRMG/?tag=skimlinks_replacement-20 Amazon.com 120mm muffin fans at $8.99 each. Has anyone looked into these low 720 RPM muffin fans for yeast starters vs those 2,400 to 3,000 RPM fans that will throw the bar magnet? My thinking why slow the speed down on a...

This may be old information but i'll pass it along. For figuring out wattage, amps, volts and watts; http://www.diyalarmforum.com/ohms-law-calculator/ Four band resistor colors, this for LED current limiting plus voltage drops; http://www.diyalarmforum.com/4-band-resistor-calc/

I picked up free a water cooler with a lower cold compartment below, has 100 watt of cooling power demand with the compressor and condenser mounted on the back. The cold water cooling coils wrap around a 6" diameter stainless can 7" deep plus another evaporator in the below cooler compartment...

see diagram

I've gone back 25 pages on both the DIY and Equipment section and have not located this posting or a reply by another member. Had it in my bier files that have been cleared out and not by me, pisser. Anyone have that posting or reply so I can wire up a 555 timer? Thanks in advance.

Did anyone see the Dirty Jobs show a couple days ago where they were harvesting Hops up in Washington state. A rather intresting show. I would of liked to of just picked off what went back into the ground as they did not strip off 100% of the hops buds, some got thru the strippers. I hope they...

This moring I talked to Matt at The CHI Company in Antelope, northern California and ordered another 4-pack of corny's. He only sells clean good condition used corny's. By this only very small dents at the most with little dings and scratches from normal service use with solid rubber bottoms and...

I have a offer to pick up a 150 cu/ft older Argon bottle a block away. Heck it has app 1/4" square stamping on it with four squares within it. It was a Linde bottle that was under Hitler's rule at one time with a swastika mark that has been restamped with four extra legs to look like four small...

I already tried to get an answer from Fred the manufacture of the Monster Mill MM3-2.0 without any luck. I asked Fred how many pounds a minute the 3roller mill will crush and at what RPM the mills input shaft is turning for the given amount in pounds of grain per minute. His reply "more than 10...

I just ordered a Monster Mill3-2.0 from Fred at Welcome to Monster Brewing Hardware I asked Fred what I should expect in pounds of grain crushed per minute and at what RPM's the mill will be turning to get these pounds per minute numbers. I'm not looking for a dead nuts accuract number just a...

I finally got awarded SSD i'm 100% disabled by a SSD court judge. Now I must wait a minimum of 120days before the first check arrives. Is the SSD check considered income and must be added to my pension income with both as taxed income? I'm new to this world of the disabled after fighting for it...

I'm in the process of designing a conical fermenter and have a question for deciding on the total volume of the fermenter needed. I like Russian Imperial Stouts and dark Porters. I will be making rather large yeast starters besides yeast and trub dumps during the fernentation, a couple times...

Today the wife came home with nine 6 packs of mixed up biers from the Nob Hill store. No Miller, Bud or watered biers. They were plastic wrapped and sold as $3.99 a 6 pack. Seems kids shoplift or adults mix and match and the stores build up mixed bier 6 packs and sell 'em cheap. I have a couple...

The CHI Company has a one more sale on corny's that will end in two days. A 4 pack in a single box for $76, $19 each before shipping, tax if your in California. They sell in 1, 2, 4, 8, 12, 20 packs and a pallet full. The 4 packs are cheaper than the other denominations offered. Matt wants...

After reading another thread posted about a boil pot with a 18" diameter asking if that would increase more boil off volume that made me think and ask a few questions almost on the same topic. First off that 18" diameter boil pot would result in 254 sq/in surface area, a 12" cut keggle 113...

The CHI Company; (530) 622-8265 here in northern California just emailed me as I buy 4 packs of corny's from them every so often. Three times the last couple months alone so far and last year a couple 4 packs. These 4 packs are shipped in one box UPS ground within a couple days. There are...

For those that build your own keggles on craigslist item # 891403966 is a complete system ready to weld with. It's a Miller DialArc w/Miller chiller,foot pedal and shielding gas (bottle) included with torch and ground clamp. Yes an older machine but a WORK HORSE. All for $600. That's a steal if...