Search results

Cheers @Thorrak, Would it be easier to set up an autoupdating chart option, or a button to reload the chart on demand (or repurpose double click to load the new chart data)? Then the visibility status of each line should be retained (I think). I've been playing round with dygraphs for a bit...

Hi all, great app @Thorrak The guys at my home brew club were talking about it last week and raving and, as I've had the last few days sick from work I thought I'd give it a spin. I've been running brewpi with arduino for years and it has been great and very reliable but the lack of any future...

Straight laced

Or double the kettle loss to take the extra sugar loss into account when doing double batches Sent from my Pixel using Home Brew mobile app

I'm running 5.12 (I think) and it outputs many many decimals

I use the one linked on thingiverse. It will work with the standard parts list easily and fit a wider variety of tubes. you can hot glue weights if required. The one with the huzzah feather will only work with that style board. That board has an integrated battery charger and has completely...

I am an idiot.

I add a 100k resistor between A0 and source so that makes it 100/(100+220+100)

I use a 100k resistor between A0 and Vbat. This gives me a nice 100k/420k voltage divider to use with the Li-ion battery voltage of 4.2V. The symmetry suits my anal retentiveness well. Although this is different to the standard design having the ability to change the battery conversion factor...

Well, 3D hubs is all down to the individual with the printer. I had a few to choose from but ended up with the one closest to work so I could pick up easily. Turned out fine. I'd be interested to see your sled. My mods were due to a different charging module.

I used 3D hubs to print a couple of sleds and it was AUD$14 for two of them. The guy did a great job but I still had to take to them with a file to get them in the tube. This was for a custom designed sled which, with the benefit of hindsight, has been customised further. I'm currently using a...

My tests today work with the diode cathode (ring) at D0. This is with a wemos flashed with iSPindel 5.12 and only temperature sensor connector. The power is supplied direct by USB. It did not work when the cathode was at the RST end. It may not have the same result when using a battery as...

I'm not sure this advice is right, According to the link you gave The RST pin is held at a HIGH signal while the ESP8266 is running. However, when the RST pin receives a LOW signal, it restarts the microcontroller. Once your device is in Deep-sleep, it will send a LOW signal to GPIO 16...

I found with the gyro led still on that I could get ~14 days from a 2200 battery with 15 minute updates. I assume that if I change the 15 minutes to 30 minutes I would be looking at 20+ days lifetime from that battery

I'm too not worried about that. The shield largely replaces the protoboard so I am not gaining much size.

This thread has been a great help in getting things up and running. At the moment I have the circuit built and connected through to ubidots and now have to print the sled to get it in the tube. It all appears to be working correctly so far. However I've done a few things differently to the...

I'm in the middle of a build of this now. I've changed up the parts a little bit but the idea is pretty much the same. I've complied and uploaded the script to the wemos and am able to get to the wifi configuration script using it as an IP, but after that, when it attempts to connect to my...

Thanks for the suggestions. It is an HDMI screen, with similar to this It can't run HDMI properly so i have had to force the LCD resolution through /boot/confgi.txt I'll attempt a custom mode, but from what I have read so far it's unlikely to work

no, apparantly the LCD resolution is fixed.

I've just build a setup for CBP (2.1) and it is looking really good. One of the elements I've built into my control box is a 5" LCD touchscreen. I plan on using that for easy on off control but would set everything via phone or desktop PC. Now the problem. The 5" LCD display is only 800x400...