Search results

I posted a while ago but didn't end up selling most of it so I'm trying one more time to get it out of my garage. Prices are lowered way below cost. Most items are only lightly used because I upgraded shortly before I stopped having time to brew. See below for items and prices. I prefer to...

Sent you both PMs.

Price cuts all around. I couldn't edit the original post for some reason so below are the new prices. This is all a fraction of what I paid, but still OBO. Will ship if needed at least for smaller items. Brew stand for two kettles /w two 100k BTU banjo burners, locking casters, and gas...

Sorry for the delay. I couldn't find the receipt and it unfortunately doesn't say on the label. I counted the sides though and it looks like 20. It works way better than my old counterflow chiller.

One last bump. Make me an offer.

Bump. May consider shipping some of it.

For anyone who is thinking about building one of these, I am selling my 2 burner setup for half what it cost several years back (San Diego area). Attached is a pic and here is my for sale post: For Sale - 10g System (together or part out) - San Diego CA I'm not sure if this sort of cross post...

Selling my full 10 gallon system because I don’t have time to use it. Most items are several years old, but were used only a couple batches because I ran out of time to brew shortly after upgrading. For now, this is all pickup only in San Diego north county. I tried to price everything at...

In case anyone is looking to build one of these in the San Diego area, I have one that I am looking to sell. The stand is great, but I’m selling all my equipment since I don’t have time to brew anymore. It is a 2 burner setup with the big 100k btu burners, heavy duty casters, and propane...

I sent you both PMs.

It has been a long time since I had time to brew, so I finally decided to sell my gear. Most items are only lightly used for a couple batches because I ran out of time to brew shortly after upgrading my setup. I prefer to sell the items together and will make a deal if people want to buy...

Thanks, these are good ideas! The kegerator is pretty new and all stainless inside, so I’d rather not modify it. The kegs from williamsbrewing look good though. The 10L won’t fit because I only have 20” of clearance and I think ball locks would put that over 20”. However, the 5L keg they...

I’m looking for a small keg (2-3 gallons) for nitro coffee that I can put on the hump of my kegerator. The 2.5g slimline torpedo keg from morebeer looked like a great fit, but it is about 1/4” too wide :(. The closest I found are the 1/2 gallon or 1 gallon pressurized growler kits (eg...

Those casters at Home Depot look great! Anyone used total locking casters like these http://www.amazon.com/dp/B000SR5YBA/?tag=skimlinks_replacement-20? Those ones get great reviews and aren't bad at $42 shipped for a set, but I can't find any info on capacity though. Anyone know if we'll get...

So I finally placed a big order with strutchannelfittings for a single tier 2 burner setup. Should have everything from them on Tuesday! After pricing it out, it was only an extra $40 or so to get everything cut by them instead of renting a chop saw and trying not to cut off a finger... Last...

Thanks. The problem with THK-205 is it would lengthen the distance of those side supports and I would need a similar piece to go between the center supports, right?

Now those are on backorder, too :(. I couldn't find a good alternative on GP-LLC. Anyone see something I'm missing or have another source?

Okay, thanks! I also will only have one burner on most of the time, so I'm not too concerned about that either. I'm just hoping we get enough BTUs on a 10 PSI regulator as I hear you only get the 200,000 BTUs if you have a 30 PSI regulator. Any consensus on the best way to mount banjo...

Thanks for the replies! I'll call strut channel fittings and see about having them cut some different sizes (my kettles are a little large, so 3' isn't long enough but 4' would be too long). Anyone else used a circular saw on this stuff? Thinking I may be better off renting a chop saw or...

I'm thinking about jumping on this bandwagon, but I'm hoping someone can help me out with a couple things: (1) I only have a handheld circular saw, so I don't think I have the necessary tools. Does anyone know if strutchannelfittings (or someone else) will cut strut to different sizes? Maybe...