Search results

Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum

Help Support Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum:

  1. harrower

    Did Northern Brewer Purchase Austin Homebrew AND/OR Adventures in Brewing?

    With current gas prices, that 2 hour drive is getting expensive!
  2. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    I picked up a Engbird Bluetooth Thermometer for my mash. I keep an eye on mash temp on my phone.
  3. harrower

    Starter yeast question

    I make a starter 24 hrs before pitching using a stir plate. After pitching, my fermentor is active within four hours. Always use a blow off tube.
  4. harrower

    Sight glass on an anvil foundry?

    I emailed brewhardware and asked about their Site Glass on an Anvil Foundry. Their reply was - "I haven't figured out a solution for a foundry yet."
  5. harrower

    Help me with my dead pump, please.

    I always test my pump before brew day. If it is making a strange noise, I take it apart and spray it with Di-Electric Grease Electrical Grade. Works every time!
  6. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    I place two needle nose vice grips on either side of the ring so that the basket does not catch the ring when pulling up the basket.
  7. harrower

    Glass or PET Carboy

    Probably causes cancer in California!
  8. harrower

    Glass or PET Carboy

    Also done with glass after trip to the ER and 9 stiches in my wrist. Pet for sure.
  9. harrower

    Upgrading propane setup vs switching to electric all in one

    When I switched from propane to an Anvil all in one, on my first brew I got out my propane burner to heat my sparge water. I then purchase a Digiboll 120 v unit to heat my sparge water. $159 then. I brew in the morning and with my Anvil I am ready to mash in first thing at 240V. I turn on my...
  10. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    Go by Anvil manual recommendations. Too little water = stuck mash during recirculation.
  11. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    No problem with gasket in 18 months of use.
  12. harrower

    Fix a stucky Chugger pump motor?

    The impeller and impeller housing. I use dielectric spray.
  13. harrower

    Fix a stucky Chugger pump motor?

    Oil the motor shafts and clean the impeller with hot water. Dry and spray with DiElectric.
  14. harrower

    Electric setup

    I brew first thing in the morning. My Anvil Foundry allows me the set the start time the night before and I am ready to mash in. The 240v system saves me a lot of time getting it up to boil.
  15. harrower

    Dry hop

    Glass Marbles
  16. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    Your getting more than just a pump with the recirculation kit. I like the screen that comes with the kit to distribute flow for recirculation and sparging. I feel that this pump is better than the March pump I had.
  17. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    Handles will be fine.
  18. harrower

    What should a yeast starter look like after 24 hours?

    I make my starters using 1 Quart of water with 8 oz of DME. 3 oz seems light. Yeast needs some starch to grow.
  19. harrower

    ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

    I bought a flow control valve from Amazon. 2-Pack In-Line Barbed Ball Valve 13mm For 1/2 Inch Tubing .520 ID - Regulate and Shut-Off/On Water Flow Quick to open-close-control flow.
  20. harrower

    That horrible feeling...

    Welding supply shop charges $10 to fill 5 lb. Filled in 5 minutes while I wait at the counter. Better to buy 2 5lb bottles than one 10 lb.
Top