Search results

I just switched to eBIAB for my 5 gallon setup. I went with a 15 gallon kettle, and glad I did. No issues with too little liquid to cover the element or too much grain that it overflows.

I had the same debate for nearly 2 weeks. It all depends on where your element end up after install. I had enough clearance on my case. Measure and measure again. You do not need a lot of clearance though. I have 1/2 inch. You can always buy the 3.5 inch standoffs and cut them down with an...

I use a false bottom during the mash. Here is what I use with 2 inch standoffs. https://www.brewhardware.com/product_p/biabbottom15.htm Feel free to ask any questions. I will be glad to give insight.

I bought a used 1.25" Greenlee punch from eBay. Cost me $40, well worth it. Very easy to use.

I personally went with a DIY version of the high gravity controller. I think you are looking at the right thing based on your needs. I really enjoy the single vessel system so far (2 brews so far.)

I brew Hefes a couple time a year. I usually let them ferment 14 days then cold crash and keg. Or bottle and wait 3 weeks to condition and carb. It will take months for the Hefe to clear up a cold temps. I was sick of Hefes a couple years back after 3 brews in a row and this happened to me with...

I have everything for plumbed in the basement (drain lines). I already finished 600sq ft of my 1200 Sq ft basement. I am trying to figure out how to create a 3/4 bath and brew room (side by side). But I just spent $500 this year on brew equipment. Wife is not enthused by that.

Just got my eBIAB setup going. Right now it is in a garage and carrying everything up and down from the basement is a pain. Hope to someday be able to run this all indoors. Currently have a cheap controller, no bells and whistles here. I am sure I will build upon it over time.

I used a HD Cooler for my MLT for 3 years before moving on. I used the following to build my bulkhead and valve. I had to get a second washer to be able to close the valve fully. (Needed extra spacing) http://www.bargainfittings.com/index.php?route=product/product&path=47&product_id=252

I almost went the HERMS but decided against it when I could not figure out what I would be gaining versus an eBIAB setup for a fraction of the cost. Went with one of wilser's bags and did my inaugural brew this weekend. Who knows I will get bored is years to come and try a HERMS setup. I...

The whirlpool performance was good. Ended up with a decent cone.

My buddy is a little unsure of the noise (pump) coming from my new setup.

Thank you! Inaugural brew day off to a good start. https://m.facebook.com/story.php?story_fbid=10100711038335337&id=6602901

Here was my progression into homebrewing... 1. Extract kits on stove top 2. Propane burner 3. All grain with cooler mash tun 4. Yeast starter 5. Keezer 6. Fermentation chamber 7. eBIAB setup If I did it over again... Fermentation chamber would be sooner. And I would have skipped the cooler...

Finished my eBIAB recirculation setup. So excited to try it out. I ran a wet test today and everything is going great. I still need to come up with a slick way to spread the return wort. Anyone have any good ideas? Trying not to spend a lot on this feature right now. Here is a video...

FIXED!!! Setting t=1 does not work. Setting t>1 works. https://drive.google.com/file/d/0Bx-zI-JTKASFMHBlU094S05OeTQ/view?usp=drivesdk

Did you ever solve this? I have a similar issue.

I am using this lid on my keggle. Only $9! http://www.ikea.com/us/en/catalog/products/60131531/ https://www.homebrewtalk.com/showthread.php?t=627019 << Picture of my keggle

I am working through Auber's Forum for Tech Support. I performed all of the suggestions and still no luck. Video of the issue: https://drive.google.com/file/d/0Bx-zI-JTKASFREk1R0JhbVRtRWs/view

I am getting to the point of buying a new PID. Spent 3 hours yesterday debugging without success. Does the MyPin have manual control? This is for an eBIAB setup.