Search results

then just thread it on any spigot and open the valve and see how much pressure you have in the system...it my house for instance my hose flows at 5gpm and i have a house pressure of about 35psi.......depending on how far you are from a pump house supplying water to the community.....you can be...

you can go to most any home improvement store and get one or even make your own...its nothing complicated......standard garden hose threads are 3/4 x 11.5 threads per inch.......just get a cap with a threaded hole in the center to fit the gauge you want to use....will look like this either way...

you will also need to measure the pressure in the water system of your house to get a better idea on what kind of pump to get. For instance.....if you hook up to a garden hose,and you end up getting like 3 gallons per minute out if your IC, then you will need a pump that can supply the same...

yep you can get center inlet polysulfone....# 0809-0179-0100 :)

you could do it with a vise at home....only thing i would do if you do it yourself is to make a support fixture for the bushing....what we use here is a spindle that fits the bore hole like the shaft would and with a wide face to support the bushing as its being pressed into the impeller....this...

I would say its not to be used for food contact areas...But check on the label of the product cause it may say other wise.....looking up the MSDS on that product, 80-99% of it is a "Hydrotreated Middle Distillates" That's a petroleum base, more then likely its a mineral oil of some sort, but its...

I was on vacation beginning of the week...first day back today....Wayne fixed it for ya...hope is all well now ;)

nothing changes inside the pump besides what you have right now....you re-use all the same stuff. Stainless shaft is (0939-0003-1000) Carbon Bushing is (0150---63-1000)

No nothing out of the ordinary here....phones are working just fine....i have had issues from the east coast before though....its weird...i've tried calling our regional sales manager a few times and got busy signals...and notice of the line being disconnected even!! then you call again right...

Wayne must be stressin out as of late.....may be the blue moon coming this friday.....if he gives you any lip about returning it to the distributor or such just send it back here to my attention. ;)

call the factory direct at 847-729-5300 and ask for Wayne :)

Sorry guys....i'm not sure why i don't get any notifications on new postings anymore... Stealthcruiser......the serial number tells me when it was built (month/year) but that's not necessarily what we go by since inventory does end to sit on some distributors shelves. If you can, send me back...

Sorry for the late reply...i never got any notification there was a new massage here till today.. Anyway you'd want to ask for the 815-SS-C beer pump and you'd get exactly what your asking for above :) our internal part number here would be 0809-0196-0900

It "sounds" like the motor may have been hit or something dropped on it maybe tweaking the alignment of the rotor out of spec.....either that or the bearing on one end of the shaft is going bad....but that's very rare unless there's a TON of hours on the motor. Look at the body of the motor for...

Are you removing the motor bracket to mount this stuff up? If so you are probably messing up the alignment of the drive magnet in relation to the pump housing. We use a jig here at the factory to center up everything. Also you will need to off set the drive magnet the thickness of the separating...

I wont get into the history between Chugger and us....but i can tell you with 110% confidence that they are NOT off the same line :) Our motors are sourced from a US based company but the factory is in Mexico...and the raw magnets come from china...then we mold them into impeller here at the...

Actually his motor was damaged...either was accidentally dropped or something fell on it. Wayne happened to have a good one in the parts dept and swapped it out. We try and help the homebrewers out as much as we possibly can (with in our limited authority here) ;)

Im only guessing without seeing it and there's not much info to go on....but my (GUESS) would be the motors tweaked. Take the pump head off and try running it.....if it runs no problem then your pump head may be misaligned. If it still doesn't work then the motors probably tweaked off center. If...

do a search for airgas they supply us with all our welding stuff and helium for testing...i know they do CO2....if they cant maybe they can suggest where to go.

Yep i found that out the hard way as well a number of years back....cleaning off some mold on a boat some bleach got spilled on my nice stainless props...few days later they look like they are 50yrs old! Here's a trick i was told by an old timer.......get a stainless wire brush...in my case i...