Search results

I’m using a 3b+. Yes, i believe plaato data comes from their website/cloud. Rpints gets info from a URL with an auth token... seems similar to (same as?) webhooks. My WiFi connection in the pi in my kegerator location is weak, so i attribute that to some of the delay.

I edited my post above. They now use "new 304 steel". Its a bit early for me to take apart my taps, but i took a video showing the flow control lever now works differently. The new one has a wider angle of rotation. The flow compensater (the half spherical metal part that sticks out the back...

The new ones don't have this problem. The lye/citric acid treatment worked for me so i bought 3 new ones a year ago and was going to do the same thing. Somewhere I read that they fixed the issue. Also when you take it apart, there are a couple parts that look a little different. I'll edit this...

With my Plaato setup, the last pour is updated without a manual refresh (local displayed connected to the pi). Sometimes there is 10-20 second day though, but I have pour wifi signal where my pi is located. Last pour was recently discussed a few posts up. You can have the amount last poured...

You really don’t need a drain within reach. You would go through 5-10 gal of waste water per hour. It’s not that hard to run it to 5 gal bucket and dump. I have a drain within reach, but usually i end up just sticking a bucket under it. I use the waste water as an initial rinse for cleaning or...

Got mine set up and working well. I didn’t have any problems with the kegs disappearing. In the taps section of rpints config, is your starting volume set to 5 gal? Looking at my config, the current amount is also a set to 5 gal as well (even though it is less than that). Not all of my kegs...

:drunk: Got it. Not sure why it didn’t update the first time. Probably user error. :drunk::drunk:

where is this new "Show last poured value" located? i did just update and can't seem to find it.

many thanks again!

cool. One last thing. It has last amount poured but is also adding total amount that has been poured as well (e.g 5 gal starting amount minus XX gal left). See pic below: “6.03 oz 1.8Gal poured”. 1.8 is from 5 gal - 3.2 gal left.

doh, that's not the first time I have forgotten a comma. That fixed it. It now echos the lastpour (e.g. lastPour=http://plaato.blynk.cc/XXXX/get/v47-8.26oz-8.26oz) ). But doesn't display this info (e.g. 8.26 oz) anywhere in rpints (i have lastpour listed as on in config section of rpints). I was...

I do not have flow meters. Just the plaato keg scales. ok makes sense. i should have looked closer at the output values. I updated under the install setion in rpints. It doesn't seem to change my index.php file. I do not have that lastPour code on line 23. Can I manually add it or are there...

I posted a pic of what i get when i remove the // from line 77. It just echos the URL rather than a value. I was hoping to get the last poured amount to display above the keg pic as shown in the pic of one of your prior posts. I posted a pic of what I mean. Perhaps I’m missing a setting to...

Kegerator

I started with these small minifridges too for fermenting and serving. Nothing wrong with doing that. The best way to get that plastic bottle holder off is to cut around the border of it with a razor utility knife taking care to leave enough of the plastic intact to preserve the gasket...

You just buy an extra keg. Always have a batch fermenting. Transfer beer to keg when you’re 4 points from predicted FG (tilt hydrometer makes this easy) and using a spunding valve to set pressure to 30-40 psi (depending on room temp and targeted vol co2). Once a keg in your keezer kicks, the keg...

When I set the tap start amount to 0 (location: taplist) then the keg image for that tap disappears. Am I changing the correct "start amount"?

You can right click the item on the raspberry pint web page that your interested in changing and choose "inspect". This can some times help you figure out which variable controls what.

Any chance we could get last pour for plaato please? :) I'm okay with those limitations.

There’s a new website. Code: curl -L install.rpints.com | sudo bash And if you can't remember that, look at rpints.com.