Search results

for the pump: Is this equivalent to a DPST toggle switch? In the "off" position, no power is delivered anywhere. When in the "on" position, it completes both circuits? For the other ones: do you have one contact that has nothing wired to it?

I don't think they make 2750W 120V heater elements. I got this number because: The 5500W elements can only produce this much power when operating at 240V. If you cut the voltage in half, to the normal 120V your wall receptacle provides, your power drops by a quarter (to 1375W). Since you have...

Ok, that makes sense. Sorry for the thread jack, but I just have one more question about how you do your mash (at least it's relevant?) So when you mash in, you pump water, then mix in grain. Let sit for 5 minutes so gravity can help settle the grain bed. Now, open MT valve fully, slightly...

If you're going to go for 240V, why not go for the ULWD 5500W 240V Camco elements? Even at 120V you can get 2750W. Do you have a 25 or 30A circuit?

Hey everyone, I'm on to what I believe are my last questions. Once they are answered, I'm going to post my electrical diagram, and physical set up to make sure there is no electrical concerns, and that everything is done properly. Here are the questions: 1.What wire gauge are people using for...

In this case, would you have the valve on the outlet of the pump partially open, and the valve on the MLT fully open? I think that's right, but just making sure

Anyone? :)

I'm on to what I believe are my last questions. Once they are answered, I'm going to post my electrical diagram, and physical set up to make sure there is no electrical concerns, and that everything is done properly. Here we go: 1.What wire gauge are people using for their 120V 15A setup...

Now that I think about it, the PID cycles the SSR, so regardless of where the switch is, the SSR will cycle. I'm on to what I believe are my last questions. Once they are answered, I'm going to post my electrical diagram, and physical set up to make sure there is no electrical concerns, and...

Awesome, thanks a lot! I'm going to follow the exact same setup, except the lid of my gang box is steel, but that won't make a difference when providing the ground. How close is the hole in the SS box to the OD of the gasket? I assume this isn't too important as the gasket is what is providing...

So there isn't a seal between the box and the element threads? Just the locknut pressing the SS box against the element gasket? Wouldn't a silicone O-ring with a washer between the box and locknut provide a near waterproof seal? Do you have plans to make this waterproof? I've been trying to...

How long does it take you to heat up sparge and strike water for a 5 gallon batch? How long does it take to bring the wort to a boil after mash out? Beautiful system!

In stlbeer's diagram, why is the element switch placed downstream of the SSR? When it's wired this way, the SSR can cycle even when the element is turned off. Isn't this unnecessarily reducing the life of the SSR? I apologize if I'm wrong, I just can't determine why the switch is after the...

I even looked at that thread, and didn't notice how useful it was! Thanks for pointing that out for me. My only question is: why isn't the element switch place upstream of the SSR? The way it's drawn, it'll switch even when the element switch isn't turned to the ON position. Although this...

Well, I'm back with yet another question! I am comfortable with wiring, as most times I'm overseen by my electrical engineer friends/workers. I can read a diagram and wire up as it shows, but I struggle trying to create my own (I believe that's common though). For all of the other people out...

I've gone through a ton of the build threads, I now completely understand the electrical system. I was just hoping to grab another opinion when asking you specific questions! I too will be buying most of my electronics from auber. I just have one more question (well, for now at least). I saw...

Where did you get the adapters for the Tee's?

I've been reading a lot about RIMS setups as I'm looking forward to making my own, and I've heard a few people who have encountered your problem. First, Once you've reached mashout temps, you should shut off your pump and heating element (if it doesnt do so automatically). Let it sit for 10...

Well, luckily this RIMS system will start out on a 5 gal system, so my step mashes will be faster than yours! :D However, once I upgrade to a single tier system, I guess I'll need to throw a burner under my MLT, or get a more powerful element and create my own circuit to run my system. I...

I guess I'll need to make sure that the outdoor outlets are 1. GFCI outlets and 2. not in the same circuit as the kitchen! MalFet, How does your 1500W element fair when heating up to mashout temps, and have you ever used it with any success for step mashes? What temp controller are you using...