Search results

I sleuthed out a possible bug (?). Every few days, I lose connection between the TiltBridge (running v2.0.0-beta1[next] (01b68ef) on an ESP32) and Brewfather. It seems that the TiltBridge "forgets" the API key for Brewfather and shows as blank on the API entry screen when the condition occurs...

Re-purposed an old KitchenAid using the spindle from a broken pasta attachment and a coupler. 8 speed on the KitchenAid delivers 180 rpm consistently with tons of torque.

I have both as well and recently switched back to a 15" high IC (with no wires between the coils). Although the CFC cools a little bit faster (but not much really), I was always annoyed by the bits of debris that would come out at the beginning of each use even with anal cleaning procedures...

Hmmm, disconnected again (reboot brought it back). Do you think it could be because I started this brew monitoring with BPR interface (which is still running) and moved over to FT2S midstream? Two feature requests - if possible, it would be good to show the name of the beer profile you are...

Do I need to do anything to 'turnoff' the BPR web interface? Was concerned if I use Lee's: sudo systemctl stop brewpi sudo systemctl disable brewpi that it would shut the whole thing down.

Our posts (edited mine) crossed in the ether. Rebooting worked. So, to your above, I should stop using the BPR web interface and only use FT2, correct? Are there any feature deltas between the two I need to consider?

Funny you should mention that. When I got up this morning, I saw the following on the controller detail page: I followed your guidance above and the installer noted some updates to components, however, I was still getting the message above after reloading the page. Rebooting the whole...

Issuing the above commands, running the FT2 config for devices, and then reenabling/restarting BPR worked. Thanks guys for the help!

Sorry, being dense, how do I delete the controller from BPR (I didn't see anything in the interface or in the BPR docs other than resetController)?

Got it. So if I just stop the current brew in BPR (just pitched yesterday, so not an issue), reboot BPR just in case, and then run the configurator, it should work or do I need to do something else?

Hmmm, configuring does not seem to be working right (do I need to literally connect the Arduino to my computer over serial versus doing it over WiFi?). I was able to configure the Fermentrack.net connection, I then tried to configure the device remotely and got this first question, not sure...

That worked, thanks for the quick update.

I installed the 'Fermentrack 2 Arduino (Serial) Support' following this page on your site. However, when I run the installer, it fails when installing the Serial to Fermentrack wheel file into virtualenv. Is there a permissions issue I need to consider? When I re-run the installer, it keeps...

In case useful to anyone, here is a visual wiring diagram (@Thorrak, please check my work!):

I ended up reverting back to BPR with Arduino and RPi as I brewed today and needed the control :) . I'll wait for the bridge you are working on to get remote capability

Hmmm. Here's a read back of my connections, please see if you see something wrong in the transplant: ESP32 pin 25 - Heat (was Arduino pin 6), connects to IN2 on relay pin 26 - Cool (was Arduino pin 5), connects to IN1 on relay pin 13 - connects to OneWire data (was Arduino pin A4) GND -...

I moved forward on replacing my Arduino/RPi with the ESP32 and FT.net. For some reason, it is not seeing the OneWire temperature sensor. I re-checked all the connections and pinouts and don't see anything wrong. Also, I am getting 5V to the OneWire sensors and they are grounded. Could the 4.7k...

Awesome, I think that guidance will get me there, will take a deeper look tomorrow. Or, should I wait for the Arduino to FT.net work you're doing now given the remote capability is what I am truly after and already have the system running?

@Thorrak, great project and thank you for all the work you have put into it! I currently am running a "traditional" headless BrewPi setup with Arduino and RPi interconnected. However, I really like the Fermentrack interface and ability to check-in/modify remotely. I assume I need to move the...

In my last few orders, it has been 6-10 days from KS to the Bay Area, regardless of when I order in the week. It seems like they only pick on Mondays and I get my order that Thursday. So when I order on a Wednesday or Thursday, I see no activity on my order until the following Monday. I stopped...