Search results

Nobody?

People, I would like to know if there are any instructions how to use Brewtroller to build my own brew controller. I implemented BrewPi myself using some instructions available here on HBT, but I not found anything simillar for Brewtroller. My setup has HLT, MT e KT (HERMS), with 2 heaters...

Works!

I will try.

I found https://community.brewpi.com/t/cannot-upload-hex-code-to-my-arduino/318/16 Now, we could wait update/upgrade code to apply on brewpi. If anyone know if was up to date, infoerm us. Thanks, Fabiano

After use "echo -ne 'E\n' > /dev/ttyACM0" my problem now is... **** Arduino Program script started **** Settings will not be restored Devices will not be restored Checking old version before programming. Checking current version: Found BrewPi v0.2.4, running commit 2a6f7f05...

People, ever after clean my Arduino Uno (EEPROM_clear or a simple sketch (// Emtpy Sketch to fix upload problem - se below) I still receiving. How to fix it? **** Arduino Program script started **** Settings will not be restored Devices will not be restored Checking old version...

People, may I add all salts on mash water and not add any salt on sparge water (only adjust pH of sparge water)? What is the potencial benefit (or not) to add all salt only on mash water? Thanks, Fabiano da Mata

@ajdelange, and about my calcs, what can you say? About #3, revisiting my calcs, I have a doubt: 3.1) Would be 1,9 mmol * 74 mg/mmol = 141 mg/L of Lime or 3.2) Would be 186,5 mg of Alkalinity/L * (74 mg of Lime/mmol) / (200 mg of Chalk/mmol) = 69 mg/L Ca++ + Ca(OH)2 + 2 HCO3-...

Multiple postage. Sorry.

Multiple postage. Sorry.

@ajdelange, look for these messeges above that were quote below. What would be right? on calcs above? Are these wrong? Sorry for reply, but how I sent multiples messeges, some of that could miss. Thanks again, Fabiano da Mata

@ajdelange, on the article, you said the "As the molecular weight of slaked lime is 74.09 each gram is 135 mM and will treat 27 mEq of bicarbonate or 1350 mg as CaCO3" I think that the right would be "....each gram is 13.5 mM..." and how we have 1 mmol of Lime for 2 mmol of CaCO3, I think that...

@ajdelange, we add chalk to shift reaction to right side?

Thanks @afr0byte and @ajdelange. More some questions: My Water report is: - Alkalinity: 186,5 mg CaCo3/L - Bicarbonate: 225,1 mg/L - Carbonate: 1,2 mg/L - Calcium: 63,6 mg/L - Magnesium: 3,4 mg/L - Total Sulfate: 0 - Nitrite: 0 - Nitrate: 0,24 mgN/L - Sodium: 4,8 mg/L - Iron: 0 - Total...

@ajdelange, thanks for your reply. Some doubt: - How change mg/L to mEq/L? - After remove the alkalinity, some Ca++ will be consumed to precipitate as CaCO3, and now to other questions: - Should I remove this precipitate to use this water on mash tun? - Should I add more Ca++ source to...

Sorry for reborn this threat. My water has Alkalinity 186,5 mgCaCo3/L and 63,6 mg/L of Ca and 3,41 mg/L of Mg. Am I candidate to use slaked lime to reduce alkalinity? I try do a simulation on Braukaiser spreadsheet and I have a result that I would like to share with you, because I intent...

@day_trippr, it is freezing. I need reboot it (unplugging power wire from wall). After reboot, it restart and work properly (until a new freeze 😓). @CGish, it freeze. I imagine that all RPi freeze, because it dont send new setpoints to Arduino, dont allow us access web interface over...

@wbarber, sorry for my English and for the sort information. My Brewpi was working good, but after some hours, the web access (it is over a lan - without internet access) was not possible and it (RPi) stop to send info (set point as programmed on Beer Profile) to Arduino. The Arduino still...

Sorry