• Please visit and share your knowledge at our sister communities:
    Cheesemaking Forum Cast Iron Forum Canning Forum Ceramic Grills
    Espresso Forum Hot Pepper Forums Pizza Oven Forums
  • If you have not, please join our official Homebrewing Facebook Group!

    Homebrewing Facebook Group

Search results

Yakima 728
Homebrew Talk

Help Support Homebrew Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. E BIAB Panel

    E BIAB Panel

    Plans for BIAB Panel
    • Herb3
    • Album
    • Comments: 0
  2. Herb3

    SS Brewing Technologies "That's a ton of Stuff!" Giveaway

    In!
  3. Herb3

    Ultra Barrier Silver Beer Hose Giveaway from Kegconnection.com!

    In!
  4. Herb3

    FastRack Party Pack Giveaway! - Open to All Members!

    In!
  5. Herb3

    Kegconnection Complete Starter Kit and More Giveaway!

    In!
  6. Herb3

    HopHouse Brewing Supply Hops Giveaway - Open to All!

    In!
  7. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    I was and I have it back to "stock" now and can view Brewpi again
  8. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    I just got the samething trying to set-up mine :confused:
  9. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    That is kinda what I was thinking. Right now I have the fan set-up to come on when there is a call for heating or cooling through a relay. When i install everything permanently I'll set the fan to run all the time
  10. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    I got my BrewPi going this afternoon and I have a question about using a fan inside my chest freezer. Should I set the fan up to run all the time, only run while heating or run when heating or cooling?
  11. Herb3

    FastRack - FastFerment Giveaway - Open to all!

    In!
  12. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    Did you include the 4.7 resistor for the temp probes?
  13. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    No everything was fine but the one temp sensor I installed just to test it out. Once I installed my other temp sensor and got a reading I was able to figure out the rest of the configuration. My SSR's where wired right and showing up but the lack of a temp reading was screwing me up :o
  14. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    Yes once I got my one good temp sensor working I was able to figure out the relays and get it all set up. Thanks!
  15. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    Yes break the tab between the brass screws. That is the hot side of the outlet. You can leave the tab connect on the other side between the silver screws. That side is your neutral.
  16. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    Thanks day_trippr. Looks like I got a bad probe. I only had one of the 2 I ordered hooked up for initial testing. I hooked up the other one and I now at least have a temp sensor reading.
  17. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    No my probes are not listed or detected :confused:
  18. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    I have under detected devices: Device 1 Pin 5(Act2) Device 2 Pin 6(Act1) Device 3 Pin A5(Act4) Device 4 4(Door) All list device type as None If I try to assign a slot nothing sticks
  19. Herb3

    HOWTO - Make a BrewPi Fermentation Controller For Cheap

    Ok I have everything wired up just like in the 1st post but no matter what I do I can not get this thing configured. Only thing that I did different was use 25A SSR's that I already had on hand. These I wire the digital 5 and 6 pins to the SSR's negative post and ran 5V to the positive post...
  20. Herb3

    Things a Homebrewer Thinks

    Is there a problem using Sam Adams bottles? I hope not because I just got a little over a case given to me this past weekend.
Back
Top