• Please visit and share your knowledge at our sister communities:
    Cheesemaking Forum Cast Iron Forum Canning Forum Ceramic Grills
    Espresso Forum Hot Pepper Forums Pizza Oven Forums
  • If you have not, please join our official Homebrewing Facebook Group!

    Homebrewing Facebook Group

Search results

SSBrew - 728
Homebrew Talk

Help Support Homebrew Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. I

    Spike Conical- observations and best practices

    Green scrubby shouldn't cause micro scratches, since polymers are much softer than metals. I use a CIP ball to clean mine, but as Jag75 mentioned I don't get much on my life either.
  2. I

    EVABarrier - Is it really that great?

    This is from MoreBeer's website Outer Barrier The outer barrier is made from EVA material and provides a decent stiffness to the tubing while still remaining pliable. This not only makes EVABarrier extremely kink resistant, it also makes it the best tubing to be used with Duotight, John Guest...
  3. I

    Taprite o-ring 440-17r

    Your local welding/gas shop will probably stock them, but it might be $2.00 each.
  4. I

    Show Us Your Stickers

    I'll show you mine, if you show me yours. :cool:
  5. I

    Plug oak barrel spigot hole b/c it leaks , how?

    If you are not worried about a spigot, get a piece of round oak rod and sand it down so that you have a tapered plug and pound it in, I believe that is how whiskey makers do it when they do it.
  6. I

    Interesting pump flow discovery/idea

    Nice table setup, where did you get the mount for the Auber? Looking to do something similar with my Auber. Appreciate the feedback.
  7. I

    Ispindel and Brewfather app

    Well I thought I had everything going for the Brewpiless. I see to be stuck on how to set the iSpindel up to run the calibration during fermentation. I go the Brewpiless to see the iSpindel but now when I am attempting to set up for the calibration I am not getting anything. I am unsure what...
  8. I

    iSpindel not communicating with BrewPiLess

    DuncB, I think I might have found the issue. I did a factory reset and the ispindel identified itself as iSpindel_iSpindel100, so it seems that the info after the underscore is what I had incorrect. Looks like that took care of it. :)
  9. I

    Ispindel and Brewfather app

    Can you provide a link to the "Nautillis relay"?
  10. I

    iSpindel not communicating with BrewPiLess

    DuncB, I calibrated the Ispindel once with sugar water and I have used it once or twice (with Fermentrack). Ispindel name is Ispindel_0001 Server Address is the one for the Brewpiless (I have tried it with the iSpindel serve address too, no luck either).
  11. I

    iSpindel not communicating with BrewPiLess

    I am unable to get my iSpindel to communicate with my BrewPiLess system. I believe I have set iSpindel up correctly for Brewpiless, but I never see any reading when I am running a profile. Anyone have a clue what I am doing incorrectly? (first image is the ISpindel page, second is the...
  12. I

    Spike Conical- observations and best practices

    I stopped using the elbow, I have the butterfly valve and a hose barb fitting and just dump straight into a small bucket (I attach a short piece of tubing to the hose barb. I have not had any problems doing it this way without issue (though some type of valve that I could control the dump speed...
  13. I

    Brewpiless controller board

    All, I am looking for a controller board design (or where to purchase) based on the Brewpiless work. I found a site The Hoppy Valley Choosing an Open Source Fermentation Controller that shows a board call "The Brewboard" that I would like to use, there isn't any link to the group that...
    • IDMaynard
    • Thread
    • brewpiless contoller boards the brewboard the hoppy valley
    • Replies: 4
    • Forum: DIY Projects
  14. I

    Native ESP8266 BrewPi Firmware - WiFi BrewPi, no Arduino needed!

    Glad you were able find it
  15. I

    Native ESP8266 BrewPi Firmware - WiFi BrewPi, no Arduino needed!

    Here is the direct link to the boards I think you are asking about. https://github.com/thorrak/thorrak_hardware/blob/master/ESP8266%20BrewPi%20Boards/Common%20Components.md
  16. I

    Native ESP8266 BrewPi Firmware - WiFi BrewPi, no Arduino needed!

    I am using the board from the Fermentrack build and just uploaded the firmware directly to the D1. The board from Fermentrack have to be built. I forget who I used to build them but pretty sure it was on the Fermentrack build page
  17. I

    Square O-Ring on Regulator

    The center of the nipple should fit an Allen wrench, remove that and replace the captive )-ring. I have one of these and I really do not like it I think mine is made by tap-rite. I also have the other style that uses a large polymer flat washer but it is a really cheap regulator which leaks...
  18. I

    Native ESP8266 BrewPi Firmware - WiFi BrewPi, no Arduino needed!

    SI i tried to use the latest version, and my unit would never update. As I mentioned I had to load an earlier version that uses USB to connect to the BeerPi, it uses WiFi to transfer data to and from the Fermentrack interface. You might try that and see if it corrects your issue.
  19. I

    Native ESP8266 BrewPi Firmware - WiFi BrewPi, no Arduino needed!

    Which version of BrewPi are you running? I have not had any luck running the newer versions (WiFI enabled) and they will not work with a USB, so I am using an older version with USB
  20. I

    HELP!! Duotight in-line regulator setup issues

    Bleed off the pressure in the keg that you filled to 20 psi and see if the regulator drops in pressure.
Back
Top