Search results

I've been hearing a lot about the harmful effects micro-plastics have on living beings and it is easy to throw up the hands and just say it's unavoidable at this point. But I just read this scientific paper on it and I thought maybe it would be good to at least try to minimize exposure (for...

That 30 was when it went to defaults in centigrade and I started raising it.. I quickly changed it back to 68.0 degrees F. I was aiming for. Unfortunately I really messed up.. When I thought it was borked I hooked up my old ST-1000 and was using that. But when I figured the Brewpi might be...

I may have wasted your time - apologies. But I just retested and the setup "seems" to be working despite the tab for temp control shows off. I saw that the web interface was showing "cooling for x minutes" and so I plugged a light into the cooling outlet and sure enough it came on. So the...

I've got a Rpi orginal, and the model 1 that I'm running now - don't think I have anything newer but I'll look around. I'll see what's for sale on the interwebs as well. Don't really have anything beyond BrewPi in mind since I haven't looked into it.. BrewPi worked (works) well for my needs...

In the event I can't get it working.. not sure there's much support anymore for the rpi #1 model and my older arduino.. that may need to be replaced if wonkers - is there a general consensus on what to replace it with? I see lots of options and at this point don't have a lot of energy to go down...

Thanks LBussy. There is no "Reset controller to factory defaults", but there is "Load defaults" which I tried. Maybe my next step is getting the stuff out of its case and looking for any clues like loose wires or whatev.

Here's when playing around with different constants/profile. Jun 30 2024 08:15:44 Arduino debug message: INFO MESSAGE 14: Default settings loaded. Jun 30 2024 08:15:56 Arduino debug message: INFO MESSAGE 13: Default constants loaded. Jun 30 2024 08:17:25 Setting profile 'RP' as active...

Thanks for your advice, I really appreciate it. I get similar messages, but the tab continues to say off.

Here's the part where I disabled the control: Jun 29 2024 16:16:26 Notification: Restarted logging for beer 'robust%20porter'. Jun 29 2024 16:17:50 Notification: Temperature control disabled Jun 29 2024 16:17:50 Arduino debug message: INFO MESSAGE 12: Received new setting: mode = o Jun 29...

Thanks! I looked at Stderr and got this (although I can view the chart and whatnot): BrewPi: wifiChecker: Attempt 1 to reach 192.168.1.1 failed (Sat Jun 29 18:30:01 AKDT 2024) ping: unknown iface wlan0 BrewPi: wifiChecker: Attempt 2 to reach 192.168.1.1 failed (Sat Jun 29 18:30:17 AKDT 2024)...

Hey hope this is an ok place to ask. I have the original (or nearly) brewpi running on a raspberrypi 1 and arduino of same vintage.. always served the purpose. Today I fired it up for a new brew and when trying to remember how to run it and clear the chart and start a new brew, I mistakenly...

English brown ale here. Thank you!

Hey agentbud, I got the lid sealed up good enough I think thanks to you. I blew on it with my lung power anyway and it held.. probably good enough for what I want. What I did was take a hand plane (woodworking tool) to the top of the Speidel and leveled it out. It was not level... dipped at the...

Thanks much! You had a good explanation.. I just wasn't having success - maybe my opening is a tad bigger so the Speidel o-ring doesn't quite fit on top, though it does seal well with the standard Speidel lid. I can try again.. maybe wasn't careful enough.

Based on your solution here I ordered the fermzilla lid that has a center bubbler hole and 2 male threaded posts for adapters - not the hop bong lid like yours. Is there a trick to getting it to seal? I've added the white Speidel o-ring to the fermzilla lid (under it and next to supplied thin...

Sure would. But a lot of these outfits have a flat minimum rate. I always check by first pricing the shipping of an item in the cart, then start adding other stuff until the shipping changes and then back off. Another trick is when I travel south (not all that often) I can go for free shipping...

Thanks for that info - but too late. I opened it up from the back. (Looks like your image). Behind that spring is a little nib that looks similar to a poppet and had a black rubber-like piece on its backside. Don't know if that is included in the rebuild kits but I did put it back together. I'll...

No, there is not. At least fountain type stuff. There is one bar (the other burned down recently) that has draft beer - you gave me the idea to inquire with them.

It is just fine slotted. I have nothing that fine other than a knife blade.. don't want to muck it up. But I'll see..

@Broken Crow Thanks much - big help. I may try Aliexpress again sometime based on recommendations such as yours.. just no more shots in the dark. That link worked fine. I'm building a cruising sailboat and have a Shurflo self-priming pump for it laying around uninstalled.. I could also give that...