Search results

Sounds odd... best place to start - https://thorrak.github.io/fermentrack/ it's a very comprehensive guide. 1. Fresh install of Raspbian, I don't know if this is necessary but I had to before I could install Fermentrack, (if you've installed fermentrack you're good to go) 2. Attached Wemos...

I should probably be asking this over on the iSpindle GitHub, but figured it less likely to get lost in translation here. The iSpindle instructions mentioned about removing a couple of bits from the boards. 4. Remove the GY-521 LED - (is this purely because the LED is a power drain, can I...

yeah mainly the sled and the Pelting, and the ability to get it delivered this half of the year. I've ordered the not complete set, in the knowledge that I might need to file down the sled to get it to fit in the pelting I've had to order from eBay. Actually saved myself a couple £s

well that sucks was just about to go and buy the iSpindle via the 3d Mechtronics site and they're all out...

Got to say though despite my initial issues, you guys have done a beautiful job on this, it looks good, easy to navigate, and anyone looking to install i'd recommend taking a quick look at the youtube videos as there are a few bits on there that that aren't in the documentation yet.

Just reading up on what state the Sainsmart relay should be in, i think it needs to be set to inverted, rather than non inverted.

Hi guys, having a few issues installing my device. First off I'm on the most recent GitHub version of the firmware. Using an RPI zero W. The board is one of Thorraks designs and its attached to sainsmart relay. When I try to configure sensors and pins the time it takes to load is very long...

Ok all installed and it looks good, on a new instance of raspbian. Used all the fully auto options. Couple of notes/questions though - it flags a couple of errors during the install but I think these are normal but might cause concern if you're installing. See picture below. - it takes quite...

Suspect not an issue but I've not been able to do a fresh install but instead tried to remove brewpi and var/www/html but it does pull up errors so I'll have to give it another go with a fresh raspbian install. Error message not particularly helpful [emoji57] but given I've not followed the...

Looks good I'll try and install tomorrow and then use for a brew next weekend!!

So a two wemos system?

Thanks Ame, i'll give those a try, i quite liked the drag and drop of Fritzing. with some help from ElChangoGuero i've pulled together some drawings that are a little tidier than the ones on the git hub, and easier for me to follow anyway, so hopefully they'll be of use to others too. 1st Pic...

Reading more into iSpindle and trying to get an understanding as to how it will all come together, will the temp probe on the iSpindle remove the need for thermowell? By that I mean will iSpindle floating in the FV connect remotely to brewpi and communicate with the fridge temp probe to keep at...

Actually kind of makes sense to create something to fill the pelting, I guess in theory you could create something with a curve of the in radius and it would fit perfectly. If not a little expensive. I suspect it'll be cheaper for me to spend the €60 and buy it via the iSpindle GitHub link...

I'm trying to make sense of and redraw the diagrams in photoshop. Taking a leaf out of the ESP brewpi lot as well I've taken a first bash at creating a board that (given the small size) would only be a few £s each. But it's my first attempt at both using fritzing as a basis and designing boards...

Thanks, i've gone through this, it's a little bit as clear as mud, i have translated though. I think i follow it up until point 6. untwist the wires.... I might try and map it onto a breadboard and share it if someone fancies taking a look to make sure its right? But that last bit attach the...

Well let me know if you manage to flash the ESP with it, I'm wondering if it's limited power of just a dodgy USB comm, the same cable and ESP chip worked with an RPI3 so I'm trying to narrow down what's gone wrong.

Hd anyone had any issues flashing the ESP8266 from an RPI zero W, was trying to reset and re flash today with no success, the command would run but nothing would happen. Ended up using a spare RPI 3 to flash it no problem. Same USB cable.

Surely turning your fridge into a red light zone might raise the chances of a yeast infection??? :pipe:

Well I've not placed the order yet, I'm struggling to visualise how it all goes together what goes into the sled etc.