Quantcast

tnbrewer371's latest activity

HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Help Support Homebrew Talk:

  • tnbrewer371
    I agree. I’ve been using my corona mill for a decade and love it. But def you need a tighter crush but as previous poster warned you...
  • tnbrewer371
    tnbrewer371 reacted to doug293cz's post in the thread HLT build help with Like Like.
    The InkBird + contactor (no need for another relay, just use a contactor w/120V coil) will draw less than 1/2 A. So, there shouldn't be...
  • tnbrewer371
    tnbrewer371 reacted to LBussy's post in the thread HLT build help with Like Like.
    It's right at the edge, you are correct, this is not enough. Do you mean will the 20A circuit run the circuit + the Inkbird + the...
  • tnbrewer371
    tnbrewer371 replied to the thread HLT build help.
    I think I’m just gonna use a general all purpose inkbird to send a relay to a contactor to turn on and off the 2000W element. I like the...
  • tnbrewer371
    tnbrewer371 reacted to Bobby_M's post in the thread HLT build help with Like Like.
    If you really only want electrics and control to heat the water to a general target temp +/- a few F, a power relay where the coil is...
  • tnbrewer371
    tnbrewer371 reacted to LBussy's post in the thread HLT build help with Like Like.
    I just saw this as a lightning deal: Digital Programmable Temperature Controller, Briidea Thermostat Heating and Cooling Mode for Heat...
  • tnbrewer371
    tnbrewer371 replied to the thread HLT build help.
    Will do thank you sir!
  • tnbrewer371
    tnbrewer371 reacted to LBussy's post in the thread HLT build help with Like Like.
    If you are going to use the two-pole, you might think about a metal box and grounding the chassis. Also be sure to use 14-gauge (or...
  • tnbrewer371
    tnbrewer371 reacted to doug293cz's post in the thread HLT build help with Like Like.
    Yes. Brew on :mug:
  • tnbrewer371
    tnbrewer371 replied to the thread HLT build help.
    But I could use a double pole now only using one pole and have it for later when I get my 240 volt Run For a future EBK and use it in...
  • tnbrewer371
    tnbrewer371 reacted to doug293cz's post in the thread HLT build help with Like Like.
    Should work. Brew on :mug:
  • tnbrewer371
    tnbrewer371 replied to the thread HLT build help.
    Guys thanks you so much. And you can’t offend me. I don’t have time to be offended when I could be learning from someone wiser then me...
  • tnbrewer371
    tnbrewer371 reacted to doug293cz's post in the thread HLT build help with Like Like.
    Hope I didn't offend you by being too basic. It's often hard to know what level of background someone else has on the internet, and...
  • tnbrewer371
    tnbrewer371 replied to the thread HLT build help.
    A two or three degree variance would be acceptable me. I’m familiar with how the inkbird works as I’ve been able to experiment with it...
  • tnbrewer371
    tnbrewer371 reacted to doug293cz's post in the thread HLT build help with Like Like.
    The InkBird ITC308 (as well as the ITC1000) are both on/off controllers with hysteresis. If the temp is below the setpoint by the lower...
Top