Recent content by saviothecnic

After a week of concussions I pulled out a PCB to connect everything. Obviously the official shield is the best solution But this is obviously not quick to make LCD and Encoder only helps to connect cleanly and fast temperature sensors, relay boards and some connector for future use or I2C...

Thanks Guys I'm sorry but between instructions in English and linux system two things for me a little lost ostiche I know: ( In practice, I did not understand how to configure the device following a bit here now seems OK;) http://docs.brewpi.com/after-install/device-configuration.html...

I have run all installations automatically As explained in the site BrewPi But it is the first time I use raspberry I may have done something wrong in the 'installation? As a user I used user pi Password raspberry Maybe I suare altor user or another command to check the...

It is as you can see from the previous post photos I also tried with no welded screw connector to ensure that it was a problem of bad contact You do not have to now connected Relay Card is also because incoming and in any case I want to check one thing at a time Thank you for your code how do...

I disconnected and re-fed everything but nothing Or should I restart with some command? I checked the probes on another circuit as in the picture and as good as an suno that the cables are the correct color red + 5V GND Black Signal Yellow I also tried to raise doubts Solder the wires to...

The black thing is nothing more than a connector clamp step 5 I used so that I can change on the fly without weld probe Place along side a photo Nothing I've tried to reverse as recommended by A4 5V Arduino pin but does not read I have not figured out how to do the test with...

Hello I'm trying also tell me if I have done well by following your pattern virtually reisstenza from 4k7 in parallel between + VCC and A4 signal of the temperature probe Question. Hex shield version should I download for A or C I have tried both but no I do not read the two...

Yes, I read your question I also applied on the same topic If we can Change Pin Out and encode a LCD I2C could use the schiedl OpenArdBir that is easy to do at home I just doubt encoder What do you say okay this? Or use it without a shield I bought this card relay And I...

Very interesting I just ordered a Raspberry http://www.ebay.it/itm/251386341241?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649 And also I have many componeti and already inside arduino I wonder but I can change the PIN out to use a shield that I have already in the house To have a...

PreTest New PCB OpenArdBir O.C Ok I am attaching files engraving PCBs and high-definition picture so are of no help to mount https://lh3.googleusercontent.com/-3Rf3W8P_sY4/U1ZQIUiq7yI/AAAAAAAAYKM/9dpFSiiAk00/w906-h504-no/ComponentiOpenArdBir.jpg Donwload PCB Files...

Great word in Relay SSR had led me astray I had not seen the pattern of the SSR from what I understand is more or less made ​​up the pattern as I posted COn the difference that in SSR is already all nice and ready in a little box with 4 contacts and LEDs: D So we were right to...

Very interesting modification would be nice to control both the pump but especially also the electric resistance in PWM I saw this card that uses a Triac what do you think? http://upload.plcwww.com/files/20/Esemp% 20fcd-triac.jpg In Italiano Molto interessante la modifica sarebbe...

Do not worry Steve we understand Our best wishes for healing for your daughter The family comes first I wish Happy Holidays to all of you

Bene oggi ho quasi terminato :D Inscatolare il tutto non è stato semplice vi posto qualche foto Come vi ho accennato ho deciso di svincolare elettronica dal blocco meccanico. Quindi ci sono dei connettori sull' elettronica e sulla parte meccanica Servirebbe un contenitore un pelo...

Video Primo Test Clone Finito 11 11 2013 http://www.youtube.com/watch?v=-2JW1j1myiI&feature=youtu.be