Recent content by Big_T

HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Help Support Homebrew Talk:

  1. B

    Michigan Ball Lock Kegs

    Pics of the 1 handle keg
  2. B

    Michigan Ball Lock Kegs

    The 2 converted pin lock kegs measure 9 inch diameter and 23 inches high. The single handle keg is slightly smaller diameter and a few inches taller.
  3. B

    Michigan Ball Lock Kegs

    I will try to get some actual measurements this week. But they should be the standard pin lock size, 5-gallon Pin Lock Keg - 8-7/8" dia x 21" H.
  4. B

    1/6 sanke kegs in keezer

    I have looked at that thread many times over. Like some have commented before some of those models are no longer available. I am really leaning toward the larger freezer so I have plenty of room but was hoping that someone might have first hand experience with the 1/6 sanke kegs.
  5. B

    1/6 sanke kegs in keezer

    I am going to be building a keezer and am not sure what size freezer to start with. I am going to be using 1/6 sanke style kegs. I plan to have 4 regular taps with room to add a stout tap. So is there anyone using a 7 cf freezer with 5 sanke kegs? I am assuming I will need to step up to a...
  6. B

    Michigan Ball Lock Kegs

    Still got the 2 converted pin locks and the single handled keg. Will let all 3 go for 120. All are empty and clean ready for pick up. Getting my stuff around to build a new keezer and want to convert to all sanke style kegs.
  7. B

    Michigan Ball Lock Kegs

    Got 2 converted pin locks lefts.
  8. B

    Michigan Ball Lock Kegs

    Only 2 left. The 2 with the yellow handles are left. These are converted pin locks. 100 for both or 60 each.
  9. B

    Michigan 1/6 barrel (5.16g) and slim 1/4 (7.75g) barrel sankey kegs

    Do you have any pictures of the kegs? Are they D-system taps? Also are the spears held in with the retaining ring or are they screw in? What is the origin of the kegs? Did you buy them new or are the out of service kegs from a brewery? Do you ever make it to the east side of the state or...
  10. B

    Michigan Ball Lock Kegs

    Willing to work on shipping these if there is interest. Not going to run around getting quotes for shipping so if you are serious figure 20 to 30 for shipping.
  11. B

    Michigan Ball Lock Kegs

    I have got 4 empty and ready to go. I have 2 true ball lock kegs that are the taller style, 3 converted pin locks (short and fatter kegs) then the single handle ball lock keg.
  12. B

    Michigan Ball Lock Kegs

    I am home after 5:30 during the week if you want to take a look at what I have available. I am going to try to bottle the beer I have in them this week and once I get them empty I will clean them and then post some pics of what I have available.
  13. B

    Michigan Ball Lock Kegs

    I am going to bottle all my beer in the kegs since I am going to be closing on a house in the next week, so all 6 will be empty and ready to go to a new home.
  14. B

    Michigan Ball Lock Kegs

    I am looking to get rid of my ball lock kegs and upgrade to using all sanke kegs. Right now I have 2 empty kegs that should be ready to go. They were used in my rotation so all seals have been replaced recently and should be good to use. There are also some with new lids so there is a PRV...
  15. B

    I think its time for a nitro set up i have questions

    I think a good test would be to take a stout that is carbed properly and then push it through the stout faucet using 30PSI beer gas and then 30 PSI CO2. That would be a more apples to apples comparison. You would need to do this with the CO2 right when the beer is finished carbing so there is...
Top