Solar HERMS setup

Hey all. I'd like to get some ideas as to how to go about doing this and whether or not you all think it is a good idea.

In Sept I've gotten the ok from SWMBO that I can build a shed/brew house. The roof of this shed is going to face South so my thought was to put a solar hot water heater on the roof and hook it up to a HERMS rig.

My main concerns are controlling the temp of the heat exchanger and then using that to control the temp of the mash, also I would like to be able to use the heat exchanger to pre-heat the strike water, etc. Any thoughts or suggestions would be great.

 

I think its an awesome idea although its going to increase your build quite a bit placing solar panels on the roof of the bewshed. No idea what a solar system would cost.

 

I don't know if I'm going to do Solar PV as well or just Solar Hot Water. There are plenty of places (instructables included) that show how to make Solar Hot Water for fairly cheap (< $100).

I apologize also because I guess this wouldn't be an actual HERMS maybe more just using Solar Hot Water to help heat my HLT.

I just thought of a concern though, my plan was to use a closed loop between the Solar Hot water box on the roof and the Heat Exchanger in the HLT. What happens when all of the water in the re-circ loop reaches temperature? Does it just keep circulating or should there be a blow off? Anyone ever install Solar Hot Water at their house?

 

I would think of setting up a parabolic reflector heating up some kind of circulating liquid medium stored in a tank and then use a heat exchanger to heat up your mash water. A bit complex but I don't think you'll be able to hit 170 easily with a black box. For temperature control I think some sort of heat exchanger would be required. Then again, I really don't know a whole heck of a lot regarding direct solar heating.

Cool concept though, very interested to see if and how it progresses. Here in Fl, we have no shortage of sunlight thats for sure..

 

Look at fresnel lenses, you can really concentrate some heat that way and put it exactly where you want it. remember burning ants with a magnifying glass?

 

Not sure if you've come across this page yet, but it's pretty good: Plans for solar thermal, PV, Wind, Heating, Cooling, Cooking, and energy saving projects for Do It Yourselfers

I think it's a great idea, I plan on getting my rig converted over to run on deep cycle batteries and trickle charge it throughout the week with a PV panel.

Good luck and keep us posted!

 

CodeRage & bdavanza, setting up a parabolic reflector or lens would be an awesome idea but I don't think I have the right set up for it unless I'm missing something.

I was reading one of the sites on the link that chispas posted and here's what I found about Flat Plate Collectors "The most efficient collector design maximizes solar heat gain, minimizes heat losses, and provides for the most efficient heat transfer from absorber plate to tube. Operating temperatures up to 250°F (121°C) are obtainable, although neither common nor desirable. Remember, you want hot water, not steam."

Now I understand that my "box" probably won't be the most efficient design but 80 degrees seems like a good cushion. I'm kind of curious if I can make it to 170. I think a test within the next week or so may be necessary.

 

According to this website: Lesson 2: Solar Hot Water Basics | Pennsylvania Solar Course, on a summers day 180 to 200 degrees is achievable.

 

Makes me think about using something like this
53" HUGE FRESNEL LENS linear solar water heater OVEN - eBay (item 170369763016 end time Aug-12-09 12:57:24 PDT)

 

Man. Looks like from that YouTube video you could just set up your boil kettle in front of that lens and let 'er rip.

Sawdust, I was thinking possibly a drain back system. We don't have the cold climates like PA but I was afraid of the stagnation temperatures of just a simple closed loop. The only thing that kind of sucks is the fact that it will involve a little more hardware (pumps etc.)

 

With the installation of my new shed i've been working on this exact project. My thought was to have the solar heat for both preheating brewing water and for general cleanup.

To keep things small my thought was to use a 15 gal keg and insulate the crap out of it with reflectix and use that as the hot water tank. Otherwise just get one of those small apartment water heaters and use it without electricity.

To test the system I was planning on just using a coil of black pipe to see what kind of temps I could get. Then later on I would upgrade to a flat collector plate.

 

If you back to back brew your IC water could be the next batch's Liquor.....

 

JC, would you use the keg or hot water tank as simply a storage vessel before the water goes to the HLT? So in other words you would do an open loop system?

 

Right, it would just be for storage. That way I could use it for brewing or for cleaning brewing equipment.

For brewing i would pump it into my HLT and then heat it the rest of the way if needed. Then i would have a much quicker preheat on the system.

 

JC, that's awesome. I didn't even think about using it for cleaning water too. Maybe I'll set up a mini sink area in the brewhouse that can be powered by this as well.

So I had a bit of a development today at work. I am an engineer at a Pool & Spa company and we manufacture heat pumps for the pool business. Apparently we scrap the cooling coils on a regular basis due to damaged fins. If I can take one of these coils home, straighten the fins a little bit, re-paint it and then put it in a glass covered box, BAM, I have a flat plate collector. SCORE!

 

I have another question regarding this setup that I'd like to get some feedback on if possible.

I think I have decided to do a drain back system as I said earlier which is basically a tank with a pump in it that will pump propylene glycol through the solar collector on the roof and then back to the tank (keg or cooler).

My thought is to put a heat exchanger in this keg/cooler and then run either my wort or HLT water through it depending on what I need.

My question is, is there any benefit to buying a Chillzilla and running the return from the solar collector through what would normally be the cooling side and run my wort or HLT water in the opposite direction through the other side like normal?

Any thoughts? I can try to do a diagram once I sober up a little if it will help.

 

So I went to work and sketched up what I thought I would do. I found a source for some good solenoid valves so I came up with a way to do it using one pump and 7 valves for the system. Here is the system and also a diagram of a drainback system.

What do you all think?