NEW Blichmann 14.5 Gallon Stainless Steel Conical Fermenter - Fermenator - MN

Below is shamelessly taken off of Blichmann's website, however the pics are mine AND on top of the standard configuration, there are also 2 additional toppers included (see pics) and 2 air locks, and spare gasket for going around the whole top. This is brand new, never used, top of the line and perfect for 10 gallon batches of beer or wine.

Price : $550, PM with offers or question
local pick up preferred as the device is 18.5"x18.5"x31.25" and weighs about 20-30 lbs, it would cost almost $100 to ship :/







read more here: http://www.blichmannengineering.com/fermentor/fermentor.html

100% Stainless Steel Everything that touches your beer is heavy gauge stainless steel or FDA approved silicone. No need to worry about what options to buy. . .it's all standard equipment!!

Weld-free Interior The Fermenator is the only weld-free interior fermentor (fernemter) on the market!! No stress about bacteria hiding in weld cracks or porosity found in all welds. Even so-called sanitary welds. The surfaces of the Fermenator where the fittings penetrate are smooth (no weld "ripples") so it is a snap to clean and sanitize. Although the weld-free fittings are more expensive than welded fittings, we think it's well worth it for peace of mind and clean, bacteria-free beer.

Guaranteed 100% Leak Free!!! Our time proven design is rock solid and the core design is identical to hydraulic systems under thousands of PSI. Even the lid seal can be fully immersed under pressure!

Easy to clean weld-free fittings All fittings used for the bottom dump and rotating racking arm are stainless steel high quality industrial fittings, not make shift hardware store parts and pipe fittings. And unlike welded fittings, ours can be removed for easy sanitizing by sanitizer, boiling or autoclaving. And our competitor's welded-in fittings can't be replaced if they get accidentally damaged or wear out! And since our fittings can be removed from the tank they are even easier to keep clean!

Last, but not least, the weld-free fittings allow you to orient the dump valve in any position you want, not where it happens to end up when tightening a welded fitting....such as facing the rear of the refrigerator!

Rotating Racking Arm The rotating racking arm is standard equipment! Just like the Craft Brewers huge conical fermentors. This feature allows you to start your siphon with the racking arm horizontal, and rotate it slowly downward until you just start picking up yeast sediment. Clearly the best and only way to siphon clear beer! And using the racking arm prevents wasting any beer or carrying sediment into your kegs which happens if you use the bottom dump to rack the beer. This exclusive design utilizes stainless flare fittings which can't hide bacteria like compression fittings can. And the valve handle shows yo the position of the racking arm at all times.

Patent pending lid hatch - easy sanitary access to your fermenting beer. Minimizes exposure of the fermentables to oxidation and bacterial contamination when dry-hopping or adding finings as opposed to removing the lid entirely. This generous size opening also makes it much easier to pitch yeast than pouring through the small stopper hole.
Patent Pending Bolted leg system - higher strength and spotless interior - Our channel shaped legs offer improved strength and appearance. An exclusive welding process is utilized to install fasteners on the tank wall leaving the interior of the tank absolutely flawless and superior to TIG welded designs where weld distortion (rippling) is unavoidable. The legs can be replaced in minutes if they are accidentally damaged! And most importantly, the legs are affixed to the tank so cleaning is much easier than designed where the tank simply sits on a stand.
Pressure Capable Stainless Lid Just like the big breweries, use CO2 pressure to pump your finished beer up to 6ft above your fermenter to your kegs. Eliminates the need for elevating the fermentor above the kegs or bottling bucket. Ideal for chest freezers. Not intended for carbonation.

Wine-makers! Forms a 100% pressure and vacuum tight seal so no need for a floating lid! The sealing system is far superior to wine tanks and is completely impervious to oxygen. Most stainless wine fermenting tanks have a loose fitting lid for primary fermentation (to vent gas) and a floating lid for secondary fermentation (to prevent oxygen infiltration). This floating lid has an inflatable seal "tire" with a "bicycle pump" and must be checked periodically to be sure it hasn't deflated. It is also a source for bacterial contamination from the fermentation material on the walls of the fermentor. The blanket of CO2 on the surface of the wine from fermentation will protect the wine from oxidation. After complete fermentation has been verified remove the airlock and stopper and replace with a stopper with no hole

Improved lid seal (click for photo) - excellent sealing and long life - Exclusive bead molded into the seal profile offers improved sealing on the tank lip further protecting your fermentables from contamination. Top quality silicone material has improved bond strength and temperature capability for long life. And the softer material conforms better to the irregular tank surface for outstanding sealing capability. Far superior to all competitive seals!
Folding Handles -fold neatly away when not in use and stay connected to the unit at all times! (Mouse-over photo for animation)



The 27 and 42 gal. units cannot be moved when full due to the sheer weight of the unit. When empty, all units are light enough to easily be carried by the handle.

Ultra Low Profile Design The Fermenator can easily be placed in a full size refrigerator or freezer for maintaining fermentation temperatures at a fraction of the cost of immersion coolers which can run well over $600. And no worry about sanitation! See Data for dimensions. And check out our FAQ section to learn how economical and easy it is to convert a freezer into the ultimate lagering chamber!

Leg Pads Plastic leg pads protect your counters and refrigerator from scratches.

Ale brewer? We have optional bolt-on leg extensions (see gallery for pic) to raise the unit for easy siphoning into a Cornelius keg. This is a great feature for brewers that want to make both ales and lagers with the same unit. Or, just place it on a counter or stand of your own.

 

price reduced to $550

 

Not to nitpick, but no it's not. Blichmann conicals are only rated to 3-5psi which is fine for pressurized transfers, but it it's not a pressure rated conical for spunding, which is mentioned in the info you snagged from their website

They're nice looking conicals, best of luck with the sale!

 

How old is the fermentor as the finish looks dull possibly the pix, shipping to 34601?

 

removed that line from the add, thanks for pointing it out.

 

Yea how old is it? It looks beat....The picture of the top looks bad......

 

That's what happens when you ferment in your front yard.

 

I'm guessing with all the leaves that cooling isn't an issue : )

 

Yeah looks like there is liquid in the air lock? Did u have it under a tarp n open air or something? Shoulda hosed it off before the pics. Even if it's never been used its obviously not new...

 

PM offer sent - RSVP

 

It is new, it is dusty from sitting in the garage, that is all.

 

This has sold locally.