Need Water Advice | HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Homebrew Talk

Help Support Homebrew Talk by donating:

  1. Dismiss Notice
  2. We have a new forum and it needs your help! Homebrewing Deals is a forum to post whatever deals and specials you find that other homebrewers might value! Includes coupon layering, Craigslist finds, eBay finds, Amazon specials, etc.
    Dismiss Notice

Need Water Advice

Discussion in 'General Homebrew Discussion' started by BrewmeisterSmith, Nov 14, 2012.

 

  1. #1
    BrewmeisterSmith

    Well-Known Member

    Posted Nov 14, 2012
    I've been brewing for a while and using the water out of my kitchen faucet. The problem is that my kitchen faucet uses soft water. I'd like to use plain old tap water. I hear that soft water creates a chalky and bitter taste. I don't see it in my more robust brews, but notice it slightly in my lighter ones. The water report for Kalamazoo is below. Without getting too complicated, what advice can be offered? Anyone from Kalamazoo? How do you use your tap water in your mash? Do you treat it first, etc.

    I'm going to try my next batch with water straight from the garden hose and just throw in a Campden tablet. I was even thinking about adding an easily connectable carbon filter to the garden hose. Looking for further advice.

    http://www.kalamazoocity.org/docs/2011WQR.pdf
     
  2. #2
    smizak

    Well-Known Member

    Posted Nov 14, 2012
    You're gonna have to ask for a more comprehensive report. That one says almost nothing about the most important minerals that are relevant to brewing
     
  3. #3
    Spartan1979

    Supporting Member  

    Posted Nov 14, 2012
    Buy an RV hose. Garden hoses aren't really for drinking water.
     
  4. #4
    Yooper

    Ale's What Cures You! Staff Member  

    Posted Nov 14, 2012
    "Soft" water may be perfect, as long as it isn't water out of a water softener which I suspect might be the case.

    Tap water may be just fine to use, depending on the composition. Alkalinity, calcium, chloride, sulfate, and sodium are important to know. If you can find that info from your water department, that would help.
     
  5. #5
    mcbaumannerb

    Well-Known Member  

    Posted Nov 14, 2012
    If you're referring to a whole house water softener, doesn't it have a bypass switch? Just engage the bypass, bleed the water out of your pipes and then use the "regular" tap water.
     
  6. #6
    whrswoldo

    Member

    Posted Nov 16, 2012
    I use a hose rigged up to a whole-house water filter (to remove chlorine, etc.), and then I add water salts. So far I have been very pleased with the results, haven't noticed any chalky or bitter tastes. It's also significantly easier and faster to fill the kettle/HLT.
     
  7. #7
    BrewmeisterSmith

    Well-Known Member

    Posted Nov 16, 2012
    Looks like I'll be building an RV hose/whole house filter setup this weekend. Thanks!
     
  8. #8
    BrewmeisterSmith

    Well-Known Member

    Posted Nov 23, 2012
    So I built the water filter tonight and it came together famously. I bought a 2 micron filter, the lowest Lowes had, and gave it a try. The water sucked! I'm going to have to order a .5 micron filter online and give it a shot. Seems no one in town carries anything less than a 2 micron. I line up 3 glasses of water for a taste test. 2 micron filtered water, tap water from the kitchen sink (from water softener), and fridge water. The fridge water was the best, which I think is softened water ran through the filter in the fridge. The water from the 2 micron filter tasted very chalky.

    Update: I went back to Lowes and found a .5 Micron filter. The water tastes fantastic now. I think the 2 micron that I had used didn't reduce the chlorine. Problem solved. Brewing tomorrow to find out how it works.
     
Draft saved Draft deleted

Share This Page

Group Builder