My Brew Build - Elm Street Brewery - Part 6 - The Fermenter

Hi everyone,

Welcome to Part 6. The Final Part

The previous posts are:

Part 1 - Introduction
http://www.homebrewtalk.com/f51/my-brew-build-elm-street-brewery-part-1-introduction-129652/

Part 2 - The Grain Mill
http://www.homebrewtalk.com/f51/my-brew-build-elm-street-brewery-part-2-grain-mill-129770/

Part 3 - The Mash/LauterTun
http://www.homebrewtalk.com/f51/my-brew-build-elm-street-brewery-part-3-mash-lautertun-129913/

Part 4 - The HLT and Keggle
http://www.homebrewtalk.com/f51/my-brew-build-elm-street-brewery-part-4-hlt-keggle-130091/

Part 5 - The Stand and Setup
http://www.homebrewtalk.com/f51/my-brew-build-elm-street-brewery-part-5-stand-setup-130795/


I had the opportunity to meet and talk to a local craft brewer. I told him about my planned home brew build and picked his brain about brewing.

For him as small brewer, one of the hardest parts of brewing is producing a good, consistent product. When he first opened the brewery his biggest issue was oxidation. He lost many batches early on to oxidation. He had to go through his whole process to find out where the oxygen was getting into the beer.

His biggest concern overall is sanitation, sanitation and sanitation.

So how does this figure into a fermenter. Well, I wanted a system that was easy to clean and sanitize, but also one that kept oxygen away from the beer. I decided to use a corny keg as a fermenter. A nice stainless steel interior which is easy to keep clean. I can also use a tank of co2 to move the beer from primary to secondary...oxygen free. Then later move it to my bottling bucket, without oxygen. I am working on a kegerator soon, so I will be able to keg most of my beer.

Here's the fermenter, blow-off container and all:



A close-up of the fermenter top. I purchased a special lid from morebeer, it has a 1/2inch coupling welded to the lid, it allows me to attach the blow-off hose to the coupling using a 1/2inch nipple:



From the top, the blow-off tube runs down to a plastic container. I drilled a hole in the lid. The hose comes in on top to a CPVC valve. A piece of CPVC pipe is at both ends of the valve. One end goes into the blow-off tube, the other through the lid, where another piece of tubing continues down to the bottom of the container. The usual sanitizing solution goes into the container. The valve allows me to close off the tube before the container, so when I pressurize the keg to move the beer, the co2 does not travel down into the container, and bubble away:

 

This is a VERY good idea for controlling and utilizing pressure. I'd love to incorporate something like this.
How do you rack into and out of this fermenter? Through that blowoff tube? Picnic tap? *Gasp* open the ...lid?

Cheers and beautiful work!

 

Sorry for the late replay. Once the cold hits here and the holiday season approaches, my homebrewing in the garage goes into hibernation. LOL. So I haven't been checking into HBT too often.

I am working with a local craft brewer to try and get his old mini brewery up and running. If I can, he'll let me use it to brew!!

Anyhow, I use a CO2 tank and hook it up to force the beer out of the primary to the secondary. Then do the same at bottling time to force beer to my bottling bucket. This process allows transfer of beer without adding oxygen!! Looking into kegging this year!!

 

That's keg lid is very cool. Morebeer no longer offers it. I like the fact the coupling is welded and threaded, and can accommodate a large diameter blow-off hose. Many possibilities. I'm searching for one similar but so far no go. I suppose I can drill my own hole, but then I lose the ability to button it up air tight.