Homemade Mash Paddle Pics

Thanks to Brewdoc22 and everyone else in this thread for giving me info to use on my paddle. I decided to get a little fancy and put my name in it.

 

I wanted to do that, sideways in Stencil, but it's beyond my skill set

 

KingKlong, did you use a scroll saw or router to letter your paddle? Nice work.

 

All of these mash paddles have motivated me. I bought the maple paddle from a restaurant supply store several years ago. I don't remember how much it cost but it was pretty cheap. I thought about lots of designs after following this thread and finally decided to pay tribute to my favorite rugby team. Go All Blacks!

 

Finished it few days ago and used with my first AG today

 

The trend seems to be wood, time to switch it up! Here's my s/s paddle. Designed in ProE, laser cut.

 

Where do you get the laser cutting done?

 

At work. I work for a company that manufactures custom commercial s/s kitchen equipment. Comes in handy when I need something for the home brewery

 

I drilled holes with forstner bits and connected them with a jig saw. Most of them were small ones. I did four in the K for instance. Same with the N. The O was one of the biggest bits in the set, and I had to step up sizes to get to it cuz the drill press didn't have enough hp to turn it through the wood.

And thanks for the compliment.

 

I could do this, but I'd be afraid it would cause me to lose my job. I drew my paddle in inventor. It would have cut quickly. There are cameras everywhere though. I also just like the look of the wood.

 

I decided I needed a replacement for the plastic spoon that came in my kit. Here's what I came up with:





It's about 36" long. I only made the paddle portion 8" because I mash in a 10 gallon cooler. Not sure I would need anything bigger. The wood is bear claw maple that I've had for years. The pictures don't do the wood justice. I left it naked and wiped it with water for the pics. I thought this would be a perfect use for it. What do you think?

 

Really neat looking maple. Looks fantastic.

 

Just wanted to share mine. A buddy got the wood from some downed black walnut trees.

 

That thing is wicked! Looks awesome!

 

badass.

 

Yup leave it naked, it more fun that way

 

That is my favorite one I've seen yet! Beautiful piece of wood. It looks full of character like it has its own personality. Also completely functional, probably more so than some of those fancy laser cut paddles. You have to remember the point of using the paddle is thoroughly mix the grains and break up the dough balls and some of those laser cut ones look nice on the brewery wall but the openings in the design don't lend themselves well to the task required. Yours is simple and has a git-er-done attitude.

WELL DONE!

 

I agree, it looks great!

But if it's not symmetric then it will try to turn in your hand when you mix the mash.

 

Never had a problem, probably cause I'm a man and i know how to wield it

 

Bazzzzinga!

 

So I've been thinking if making my mash paddle. The ol plastic spoon sucks. Can I use a reg 2 by 4? Prolly a stupid question. If not what kinda wood should I use? Thx everyone for the answers. Cheers everyone

 

I used a 1x4 maple, but I'm sure a 2x4 will work, also oak.

you want to use a hardwood, and I wouldn't use pressure-treated.

 

Construction lumber is made of pine. It is a softwood with a very loose grain. It does not do well when it gets wet repeatedly. That's why they use green-treat lumber in exposed places and you certainly don't want to use that in your beer! Your time would be better spent on a nice piece of hardwood. Your local lowes or home depot should have 1x4 pieces of various hardwood (maple, oak, walnut) in 3 or 4 foot pieces that are reasonably priced. They have nicer grain and will last a long time. Once you make the paddle finish it with some mineral oil or butchers block oil (some skip this step) and let it dry before you brew. I usually oil mine after the brew day is over so it is ready for the next time.

Good luck!

 

Wow... I certainly hope nobody's using pressure-treated lumber!
Mmmm.... cancer beer.

 

Just finished mine. Hard maple with no finish.

 

made mine a while ago. pretty fun little project.
I've since added volume marks so I can use it to measure volume in my kettles as well.

 

Got inspired by this thread and knocked one out last weekend with my hometown sports teams.

Just an oak board from Lowe's.

 

this mash paddle conflicts with your stated location.

 

where I live nobody is from around here

 

so where exactly are you from?

<hides>

 

Yeah, I've moved a bunch of times, but Boston will always be considered home.

 

Ya I want something similar to this one. Very nice.

 

great craftsmanship. I love equipment pr0n.

 

Nice

 

Here is mine from today, Oak board. No finish. Template designed in Solidworks. Holes have a burnt finish.

 

BRplatz, did you just use a torch to "toast" your paddle? Looks nice.

 

Yup I just have a MAPP/Propane torch and just tried to burn the insides enough to be black, trying to avoid the outside, then sanded it back down.

40, 120, then 240 grit. Might do more but I think it's plenty smooth

 

Please report back after using your paddle. I've noticed that if I don't oil mine, or if its been a while, the grain will swell a bit. I'm curious if the torched spots will be more sealed. I may just make another paddle and give it a light toasting with the torch and then sand it and see how it works.

 

Will do, my next brew is an imperial stout so if a little smoked oak flavor is imparted I won't mind haha

 

one hour
one piece of maple
one Dewalt recipt saw..with wood/metal combo blade
one hole saw
bit of sand paper



Its not perfectly straight but I like it.