Building a hop spider questions | HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Homebrew Talk

Help Support Homebrew Talk by donating:

  1. Dismiss Notice
  2. We have a new forum and it needs your help! Homebrewing Deals is a forum to post whatever deals and specials you find that other homebrewers might value! Includes coupon layering, Craigslist finds, eBay finds, Amazon specials, etc.
    Dismiss Notice

Building a hop spider questions

Discussion in 'Equipment/Sanitation' started by Tim-boSlice, Feb 2, 2014.

 

  1. #1
    Tim-boSlice

    Member

    Posted Feb 2, 2014
    I am building a hop spider and after reading online that some people had issues with melting PVC I decided I wanted something sturdier. I picked up a 4 inch to 3 inch galvanized steel reducer. I know galvanized steel is not a good choice for brewing or sanitizing but is using it above boiling wort an issue also? It should not be in contact with the wort at any time. Also the carriage bolts I bought are zinc plated. Any issues with that? Thanks in advance.
     
  2. #2
    eastoak

    Well-Known Member

    Posted Feb 2, 2014

    you won't regret using stainless, ever.
     
  3. #3
    WTWjr

    Well-Known Member

    Posted Feb 2, 2014
    +1 on using stainless steel. I built mine using an insinkerator garbage disposal ring and stainless steel nuts and bolts. the whole thing cost less than 25 bucks.
     
  4. #4
    reelmower

    Well-Known Member

    Posted Feb 2, 2014
    My hop spider is suspended over the brew kettle .. with hard wood dowels .. replacing the stainless threaded rod .. you see in some diagrams and plans for creating. A Stainless steel clamp .. plumbing section from the "The Big Box" .. a short piece of 1.5" diameter Sch40 PVC .. and a one gallon paint strainer bag. Drill the holes for the dowels with your hand drill .. hang it over the top of your kettle. I've never had a problem that I know of ... with the PVC. The PVC does not touch the wort .. and I've never notices any melting ... dripping .. or off flavors.
     
  5. #5
    reelmower

    Well-Known Member

    Posted Feb 2, 2014
    .. a tomato can works well too. It may not be the ideal material .. but it did hold "tomatoes" .. that may have been "cooked in the can" .. so the can received some sort of "food grade treatment". Still .. it's not touching the wort .. but is just holding the hop bag .. open .. and in place.

    Just an idea ..
     
  6. #6
    BigFloyd

    Well-Known Member

    Posted Feb 2, 2014
    I used schedule 40 PVC on mine and have never even noticed it getting soft.
     
  7. #7
    Tim-boSlice

    Member

    Posted Feb 2, 2014
    The tomato can is interesting...should I ditch the galvanized steel since it's not stainless? What about the zinc plated bolts?
     
  8. #8
    E_Marquez

    Well-Known Member

    Posted Feb 3, 2014
    [​IMG]

    Used for the third time just now,, as in,, right now..
    Love it and would build again.

    $8.00 Stainless Steel Sink drain
    $1.50 Stainless Steel worm gear clamp
    $.58 paint strainer

    and some stainless steel all thread, nuts and such I had in the scrap pile from past projects.

    15 min to build.

    And a Hop spider that is all stainless steel except the bag, no worry's of melting, made cheaply and holds 5 oz of hops with ease, no crowding.
     
    Staestc likes this.
  9. #9
    MaxStout

    Well-Known Member  

    Posted Feb 3, 2014
    +1 on the Insinkerator flange.
     
  10. #10
    titansvol

    Well-Known Member

    Posted Feb 3, 2014
    I use PVC without an issue
     
Draft saved Draft deleted

Share This Page

Group Builder