55 gal SS Drum Fermenter - need advice | HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Homebrew Talk

Help Support Homebrew Talk by donating:

  1. Dismiss Notice
  2. We have a new forum and it needs your help! Homebrewing Deals is a forum to post whatever deals and specials you find that other homebrewers might value! Includes coupon layering, Craigslist finds, eBay finds, Amazon specials, etc.
    Dismiss Notice

55 gal SS Drum Fermenter - need advice

Discussion in 'Fermenters' started by Ranger9913, Mar 14, 2011.

 

  1. #1
    Ranger9913

    Well-Known Member

    Posted Mar 14, 2011
    I recently purchased 4 55g SS drums and converted them all to kettles. However, I decided to use one right as a fermenter until I got a big enough conical. These were all closed top heads and I cut about a 10" diameter hole in the top to allow for cleaning. I also installed a 1/2 ball valve 6" from the bottom. It is sitting on a 1ft tall rack so my plan is to simply open the ball valve to rack the beer of the yeast bed to my pump and put into 15.5g kegs to carb.

    Anyone see a problem with this or have a better solution for racking.


    In case you are wondering I made a top to function the same way these conicals do.
     
  2. #2
    wyzazz

    Well-Known Member

    Posted Mar 14, 2011
    Your ball valve is only 18" from the floor & a Sanke keg is around 24" tall, you will want the ball valve to be at least that high to gravity feed the beer to the kegs. Other than that, it sounds like a good plan!
     
  3. #3
    Ranger9913

    Well-Known Member

    Posted Mar 14, 2011
    Well I have a dedicated pump i am going to use for to move the beer between fermenter and keg. Although, if my lid can hold 3-5psi I will move it with CO2
     
  4. #4
    itsme6582

    Well-Known Member

    Posted Mar 14, 2011
    Look into rotating racking arms. That will allow you to adjust your diptube height so you can rack more beer and leave the trub behind.

    Using a pump to move beer to a keg seems a little much. You'd have to sanitize it before you use it and then clean it when you're done. It just seems easier to raise the fermentor and let pressure do the work (it's pressure that does the work, not gravity). CO2 seems more simple than a pump but again I'd rather use height.
     
  5. #5
    wyzazz

    Well-Known Member

    Posted Mar 14, 2011
    Agreed, if you're not constrained by ceiling height I'd just raise the fermenter up a bit.
     
  6. #6
    Ranger9913

    Well-Known Member

    Posted Mar 14, 2011
    Okay I see your point. I will also have it on 5" casters so that 22" in which I should probably move it up another 4" to give me 26".

    I am actually going to build the rack today so I should should make the legs 16" then. I was going to build an 18"x18" square frame with 16" legs out of 1"x1"x1/8" angle iron. That should hold 300#lbs right?
     
  7. #7
    Ranger9913

    Well-Known Member

    Posted Mar 14, 2011
    In case any is interested, I found this[​IMG] at Home Depot and saved me a lot of welding and cutting.
     
  8. #8
    wyzazz

    Well-Known Member

    Posted Mar 15, 2011
    Looks kind of thin, what is it made to hold? A hot water tank? I'm assuming it will hold the drum full of wort with no issues.
     
  9. #9
    Ranger9913

    Well-Known Member

    Posted Mar 15, 2011
    I just set it up and it is thin but it's sturdy and rated for 40-100 gallons tanks. Not bad for $30.00
     
  10. #10
    Ranger9913

    Well-Known Member

    Posted Mar 15, 2011
    It is a little thin but it's sturdy as can be. It's rated for 40-100 gallon tanks. Not bad for $30.00

    1BBL.jpg
     
  11. #11
    Cpt_Kirks

    Well-Known Member

    Posted Mar 15, 2011
    Thirsty much?

    :mug:
     
Draft saved Draft deleted

Share This Page

Group Builder