Recent Content by Wilberforce | HomeBrewTalk.com - Beer, Wine, Mead, & Cider Brewing Discussion Community.

Homebrew Talk

Help Support Homebrew Talk by donating:

  1. Win a Brew Kettle or Ferm Tank from Delta Brewing Systems!
    Dismiss Notice
  2. We have a new forum and it needs your help! Homebrewing Deals is a forum to post whatever deals and specials you find that other homebrewers might value! Includes coupon layering, Craigslist finds, eBay finds, Amazon specials, etc.
    Dismiss Notice
Win a Brew Kettle or Ferm Tank from Delta Brewing Systems! Homebrewing Deals

Recent Content by Wilberforce

  1. Wilberforce
    Post

    Stc-1000+

    I'm curious - why use a arduino yun at $70 when you can use a raspberry pi at $35? Is it about the stability of using a micro controller?
    Post by: Wilberforce, Apr 15, 2014 in forum: Fermenters
  2. Wilberforce
    Post

    Stc-1000+

    Hi Mat, Now that you can flash the EEPROM separately, I'm wondering about the possibility of reading the settings, and writing them back in a...
    Post by: Wilberforce, Apr 8, 2014 in forum: Fermenters
  3. Wilberforce
    Post

    Stc-1000+

    This one has a single ssr output , who knows what the chipset is! http://www.dx.com/p/xmt612-pid-1-2-pid-temperature-controller-black-205178
    Post by: Wilberforce, Apr 8, 2014 in forum: Fermenters
  4. Wilberforce
    Post

    Stc-1000+

    Ha - that's funny! I added it so I'd have a reference to the forum, git page and forum, and my wiring - I was going to fill in the back story...
    Post by: Wilberforce, Apr 8, 2014 in forum: Fermenters
  5. Wilberforce
    Post

    Stc-1000+

    One option is to add to the arduino serial commands, 'v'. It could show the code version, and possibly EEPROM content version if you go that way....
    Post by: Wilberforce, Apr 1, 2014 in forum: Fermenters
  6. Wilberforce
    Post

    Stc-1000+

    Sorry - I was not clear. If it was on the menu, it would be a read only item - the up/down would not have any effect - only exit up a level....
    Post by: Wilberforce, Apr 1, 2014 in forum: Fermenters
  7. Wilberforce
    Post

    Stc-1000+

    Is there room on the setup menu to add ver menu? Then you could show the firmware build number. This would be useful for determining if a unit...
    Post by: Wilberforce, Mar 31, 2014 in forum: Fermenters
  8. Wilberforce
    Post

    Stc-1000+

    I managed to flash a v1.0 with the etherten board. It was a wiring issue, I had the vcc going to the arduino vin, rather than vcc. Dooh. How it...
    Post by: Wilberforce, Mar 31, 2014 in forum: Fermenters
  9. Wilberforce
    Post

    Stc-1000+

    The stickers on the outside of the units have slight differences. Perhaps we can determine a v1.0 board From the graphics?
    Post by: Wilberforce, Mar 31, 2014 in forum: Fermenters
  10. Wilberforce
    Post

    Stc-1000+

    That is surprising as I thought there was only 500ma on a USB port.
    Post by: Wilberforce, Mar 30, 2014 in forum: Fermenters
  11. Wilberforce
    Post

    Stc-1000+

    The source shows this ID Serial.print("Device ID is: 0x"); Serial.println(deviceid, HEX); if((deviceid & 0x3FE0) == 0x27C0){...
    Post by: Wilberforce, Mar 30, 2014 in forum: Fermenters
  12. Wilberforce
    Post

    Stc-1000+

    What power supplies are people using? Is 1amp enough to run the uno and the stc-1000? Thanks
    Post by: Wilberforce, Mar 30, 2014 in forum: Fermenters
  13. Wilberforce
    Post

    Stc-1000+

    I uploaded to a freetronics ether 10 board. The detect seems to be sporadic, and it won't flash, I get the following STC-1000 NOT detected....
    Post by: Wilberforce, Mar 30, 2014 in forum: Fermenters
  14. Wilberforce
    Post

    Stc-1000+

    I have a rev 1.1 power board unit like Disney7. I can't read the chip markings, however it does have 20 pins. Iscpdat and iscpclk appear to the 7...
    Post by: Wilberforce, Mar 30, 2014 in forum: Fermenters
  15. Wilberforce
    Post

    Stc-1000+

    Thanks Mat for sharing this project. I have been controlling my mash with a custom written node.js app on a raspberry pi. I was wondering how much...
    Post by: Wilberforce, Mar 27, 2014 in forum: Fermenters
Group Builder