Media RSS feed for all media by user pogden. Tue, 28 Jan 2020 01:09:06 +0000 Tue, 28 Jan 2020 01:09:06 +0000 Media https://www.homebrewtalk.com/forum/media/users/pogden.101790/index.rss SSVR eBIAB Controller Wiring Diagram Thu, 19 Jun 2014 06:06:10 +0000 https://www.homebrewtalk.com/forum/media/ssvr-ebiab-controller-wiring-diagram.63157/ https://www.homebrewtalk.com/forum/media/ssvr-ebiab-controller-wiring-diagram.63157/ invalid@example.com (pogden) pogden

ssvr_ebiab_controller-63157.jpg

I use my 4-wire dryer receptacle for power. This controller does not require 120V for anything, so I just capped the neutral wire from the incoming HHNG cord with a wire nut. EDIT 06/18/2014: Corrected pin labeling on potentiometer (swapped 1 and 3).


]]> Silver-soldered Tri Clover ferrule for element Wed, 08 Jan 2014 15:00:04 +0000 https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61804/ https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61804/ invalid@example.com (pogden) pogden

img_20140104_090733-61804.jpg

The tool disassembled.


]]> Silver-soldered Tri Clover ferrule for element Wed, 08 Jan 2014 15:00:03 +0000 https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61803/ https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61803/ invalid@example.com (pogden) pogden

img_20140104_090600-61803.jpg

The tool disassembled.


]]> Silver-soldered Tri Clover ferrule for element Wed, 08 Jan 2014 15:00:02 +0000 https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61802/ https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61802/ invalid@example.com (pogden) pogden

img_20140104_090342-61802.jpg

Here's the tool I made for pulling the dimple. I bought the SS concentric reducer from Amazon, everything else came from HD. The bolt is 15/16" x 6" long.


]]> Silver-soldered Tri Clover ferrule for element Wed, 08 Jan 2014 15:00:01 +0000 https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61801/ https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61801/ invalid@example.com (pogden) pogden

img_20140104_084854-61801.jpg

Another view. I positioned it as close as I dared to where the sidewall curves under to meet the skirt.


]]> Silver-soldered Tri Clover ferrule for element Wed, 08 Jan 2014 15:00:00 +0000 https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61800/ https://www.homebrewtalk.com/forum/media/silver-soldered-tri-clover-ferrule-for-element.61800/ invalid@example.com (pogden) pogden

img_20140104_084757-61800.jpg

Using the technique described in the massive "Soldering Stainless Steel" thread I drilled, punched, dimpled and soldered a 1.5in Tri Clover long ferrule near the bottom of the kettle. This is where my element mounts.


]]> Bottom drain keggle, Part 1 Wed, 08 Jan 2014 14:49:30 +0000 https://www.homebrewtalk.com/forum/media/bottom-drain-keggle-part-1.61799/ https://www.homebrewtalk.com/forum/media/bottom-drain-keggle-part-1.61799/ invalid@example.com (pogden) pogden

p1010482-61799.jpg

Done. In fact, the hole was just a hair too small for my lid. I was able to enlarge it just a bit with a flap disk, which was needed to smooth the sharp edge anyway.


]]> Bottom drain keggle, Part 1 Wed, 08 Jan 2014 14:49:29 +0000 https://www.homebrewtalk.com/forum/media/bottom-drain-keggle-part-1.61798/ https://www.homebrewtalk.com/forum/media/bottom-drain-keggle-part-1.61798/ invalid@example.com (pogden) pogden

p1010481-61798.jpg

I'm not sure if there is a proper technique for this, but I just worked slowly around and around until through.


]]> Bottom drain keggle, Part 1 Wed, 08 Jan 2014 14:49:29 +0000 https://www.homebrewtalk.com/forum/media/bottom-drain-keggle-part-1.61797/ https://www.homebrewtalk.com/forum/media/bottom-drain-keggle-part-1.61797/ invalid@example.com (pogden) pogden

p1010480-61797.jpg

It is just unbelievable how loud this is - be sure to where ear and eye protection.


]]>