Evaluating the Crush
work in progress
--Kaiser 22:00, 24 December 2007 (CST)
When brewing all grain, the quality of the crush has a major impact on the brew house efficiency as well as the lautering process. In extreme cases, a poor crush can also lead to astringent off flavors.
The ideal crush for malt exposes all the endosperm as flour and grits and leaves the husks intact. But in practice this is difficult to achieve. In order to expose as much of the endosperm as possible, the malt has to be crushed very tightly which leaves most of the husk material shredded. This can lead to stuck sparges astringent off-flavors. Conversely, when the malt is milled loosely the husks are preserved better but a considerable amount of the endosperm remains unexposed which will result in a loss off efficiency. Because of this the brewer needs to find a good compromise for setting the grain mill spacing.
What to look for
- flour to grits ratio : the more flour the higher the efficiency but also the chance for a slow lauter or stuck sparge
- average size of the husk pieces : the larger the husk pieces, the better they will be able to suspend the grain bed during lautering which helps with the run-off speed and prevents stuck sparges
- small husk shreds : small husk shreds can inhibit the run-off like flour and can be a significant contributor to astringent off-flavors.
- not or poorly crushed kernels : If a kernel has not or only slightly been crushed, the mash may not be able to convert the starches and/or extract the sugars. This will lead to a lowered brewhouse efficiency.
- when endosperm remains in a crushed kernel, does it easily come out when the kernel is picked up? : There is no problem with pieces of endosperm remaining in connection with the husks. As long as they come off easily or can easily be reached by the mash water.
2 roller mill dry
This crush has been produced with a 2 roller mill (JSP Maltmill) at its factory setting of 36 mil / 0.92 mm. At this setting, which is fairly loose, no substantial husk shredding occurs while the endosperm is mostly ground into grits. Some of the endosperm is left behind in the husks. The low percentage of flour and well preserved husks will make for easy lautering. But even with well modified malts, the brewhouse efficiency will be average.
At a much tighter setting (19 mil / 0.48 mm), the same mill will produce considerably more flour and shredded husks. While the efficiency is significantly increased, the lauter may not run as easily and may even get stuck if the allowed run-off speed is to great. As long as the mash and lauter pH are well below 5.8, no significant tanning extraction should be expected even though more of the husks have been shredded. The increased brewhouse efficiency makes this the crush of choice for many brewers.
2 roller mill conditioned
In order to better preserve the husk during milling, Malt can be conditioned with moisture before milling. This makes the husk less fragile which results less small husk pieces even at a very tight mill setting.
For this crush, the malt has been conditioned. The mill didn't tear the husks apart (only few of the husks were actually split in two halves) as it did with a dry crush. As a result some of the endosperm actually remained in the husks. But most of that endosperm actually falls right out of the husks when they are picked up and slightly rubbed between the fingers. The expected brewhouse efficiency should be similar to a dry crush. In the close-up picture, the husk in the lower left corner even shows the indentation of the teeth of the malt mill roller. This illustrates how plyable the husks have become through the malt conditioning.
Even at a tight setting the husks of well conditioned malt remain intact while most of the endosperm is crushed into flour. The is a very small amount of husk shreds compared to a dry crush at the same setting which mitigates one of the problems of a tight crush. Having most of the endosperm crushed to flour will boost the brewhouse efficiency but also impede lautering. Some of that can be gained back by having the husks preserved.
examples of a poor crush
This "crush" has been produced with a food processor. It is not really a crush as a food processor has spinning blades which chop the malt rather than crushing it. The result are kernels that have been broken in a way that makes it difficult for the mash to reach the endosperm which will severely limit the brewhouse efficiency. Rather then preserving the husks, the spinning blades produced a lot of very small husks shreds that will impede the lautering speed and may also contribute astringent off-flavors. A food processor is unsuitable to crush malt for brewing.
The only exception would be huskless malts like wheat malt and Weyermann's Carafa special malts. The latter are de-husked roasted malts. While the thoughput of a food processor is not enough to process a batch of wheat malt it may work work well for the Carafa Special malts since only a small amount is generally used in a recipe.
This uneven crush has been produced with