ANOTHER keg issue. - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Bottling/Kegging > ANOTHER keg issue.

Reply
 
Thread Tools
Old 12-22-2008, 11:42 PM   #1
STAD
 
STAD's Avatar
Recipes 
 
Sep 2008
San Jose, California
Posts: 633
Liked 2 Times on 2 Posts



Okay so I'm on my second kegged batch, and everytime I connect the beer out disconnect to the OUT post on the keg, it is an absolute b!tch to get off. It doesn't seem to push down all the way either. My guess is that the smart guy that I bought these kegs from has two gas posts installed. Does this sound about right?

If so, now that there is already beer in the keg, what are my options? It's truly a four letter word fest trying to get the disconnect off...
__________________
Primary: EdWort's Haus Pale Ale
Bottled:
Kegged:
Up next: Peanut Butter Porter

 
Reply With Quote
Old 12-22-2008, 11:48 PM   #2
TwoHeadsBrewing
 
TwoHeadsBrewing's Avatar
Recipes 
 
Feb 2008
Chico, CA
Posts: 3,924
Liked 39 Times on 36 Posts


Make sure the black one goes to the "OUT" connector, and the gray one goes to the "IN" connector. Sorry if this you already know this, but when I got my kegging system I had no instructions and had to learn it the hard way. If you're putting the right connectors on the posts, it could in fact be that they attached to "gas" posts to both sides. Usually, the nut on the gas posts have little notches in them, whereas the liquid posts are normal nuts. Other styles have the gas posts with 12-point heads, and the liquid is a 6-point.
__________________

Fermenting: ESB
Kegged: Extra IPA, Brown Ale, American Wheat, Blackheart Stout
Coming Up: Dunkleweizen, 3C Pale Ale


DIY Fermentation Chamber
More Brew Stuff

 
Reply With Quote
Old 12-22-2008, 11:57 PM   #3
Jonnio
 
Jonnio's Avatar
Recipes 
 
Dec 2007
Posts: 1,509
Liked 7 Times on 7 Posts


yup, if both posts look the same then you have two gas posts...or your supplier gave you two gas couplings.

If the keg is at pressure or slightly low on CO2 it wouldn't hurt a lot to try and put the CO2 connector on the out as well. It might re-suspend any yeast you have on the bottom, but that's it. (If your keg is at higher pressure than the gas line then it can flow beer back into the regulator which is a bad thing)
__________________
------------------------------------------------
Official member of HBAMAP (Home Brewers Against Murder and Pedophilia)
Quote:
Originally Posted by Revvy View Post
Then that means dumping your beer because you think it's bad is tantamount to abortion! And as Big Kahuna says, drinking a beer too soon is tatamount to beer pedophilia...

 
Reply With Quote
Old 12-23-2008, 12:00 AM   #4
STAD
 
STAD's Avatar
Recipes 
 
Sep 2008
San Jose, California
Posts: 633
Liked 2 Times on 2 Posts


Quote:
Originally Posted by Jonnio View Post
yup, if both posts look the same then you have two gas posts...or your supplier gave you two gas couplings.

If the keg is at pressure or slightly low on CO2 it wouldn't hurt a lot to try and put the CO2 connector on the out as well. It might re-suspend any yeast you have on the bottom, but that's it. (If your keg is at higher pressure than the gas line then it can flow beer back into the regulator which is a bad thing)
It's already fully carbed, so I don't think this would be a great idea, haha.
__________________
Primary: EdWort's Haus Pale Ale
Bottled:
Kegged:
Up next: Peanut Butter Porter

 
Reply With Quote
Old 12-23-2008, 12:04 AM   #5
caskconditioned
 
caskconditioned's Avatar
Recipes 
 
Jun 2007
Colorado
Posts: 175

I've dry-hopped an already carbed beer in the past. Just use the pressure relief valve to let the head pressure out (slowly). Then quickly switch the posts out. Then purge it a couple times and re-apply head pressure. If you do it fast you should be OK.

 
Reply With Quote
Old 12-23-2008, 12:07 AM   #6
STAD
 
STAD's Avatar
Recipes 
 
Sep 2008
San Jose, California
Posts: 633
Liked 2 Times on 2 Posts


Homebrewing, kegging, and fast don't really go in the same sentence with me... I'll do my best. I still have to figure out if it's truly a gas post on the beer out side. Is there a cosmetic difference I could look for?
__________________
Primary: EdWort's Haus Pale Ale
Bottled:
Kegged:
Up next: Peanut Butter Porter

 
Reply With Quote
Old 12-23-2008, 12:12 AM   #7
caskconditioned
 
caskconditioned's Avatar
Recipes 
 
Jun 2007
Colorado
Posts: 175

The gas posts usually have an line etched to the post. These are gas posts:


 
Reply With Quote
Old 12-23-2008, 12:12 AM   #8
Jonnio
 
Jonnio's Avatar
Recipes 
 
Dec 2007
Posts: 1,509
Liked 7 Times on 7 Posts


Quote:
Originally Posted by STAD View Post
Homebrewing, kegging, and fast don't really go in the same sentence with me... I'll do my best. I still have to figure out if it's truly a gas post on the beer out side. Is there a cosmetic difference I could look for?
Yeah, that's what TWOHEADS was talking about. For mine, the part that actually screws into the keg is either a 6 point or a 12 point, 6 point for beer out and 12 point for gas. As far as hooking your CO2 up to the out, I did it by accident just last night (tired and not paying attention) and it doesn't hurt anything. Like I said, the issue would be if the keg is at 15 psi and the CO2 is at say 10. That will force beer up the CO2 line if you don't have check valves.
__________________
------------------------------------------------
Official member of HBAMAP (Home Brewers Against Murder and Pedophilia)
Quote:
Originally Posted by Revvy View Post
Then that means dumping your beer because you think it's bad is tantamount to abortion! And as Big Kahuna says, drinking a beer too soon is tatamount to beer pedophilia...

 
Reply With Quote
Old 12-23-2008, 12:25 AM   #9
STAD
 
STAD's Avatar
Recipes 
 
Sep 2008
San Jose, California
Posts: 633
Liked 2 Times on 2 Posts


And the whole purpose of putting the CO2 line on the beer out is the test to see if it's a gas post, right?
__________________
Primary: EdWort's Haus Pale Ale
Bottled:
Kegged:
Up next: Peanut Butter Porter

 
Reply With Quote
Old 12-23-2008, 12:30 AM   #10
Jonnio
 
Jonnio's Avatar
Recipes 
 
Dec 2007
Posts: 1,509
Liked 7 Times on 7 Posts


yeah - like I said, its up to you if you want to try it, but that's one way to check it...before you do though, are you sure your kegerator has proper CO2 in and beer out connectors?

I guess if the keg posts are different and appear to be correct then I would put the beer out line on the CO2 in and see if it fits. If it does then you have found out that the kegerator is the problem
__________________
------------------------------------------------
Official member of HBAMAP (Home Brewers Against Murder and Pedophilia)
Quote:
Originally Posted by Revvy View Post
Then that means dumping your beer because you think it's bad is tantamount to abortion! And as Big Kahuna says, drinking a beer too soon is tatamount to beer pedophilia...

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
keg top issue Chris Z Bottling/Kegging 7 05-12-2009 03:36 PM
BYO issue? RonRock Beginners Beer Brewing Forum 5 01-24-2009 03:51 PM
Possible Keg Issue - How to fix? briandickens Bottling/Kegging 6 09-07-2007 01:09 PM
OG Issue badnaam Extract Brewing 1 06-02-2007 02:18 AM


Forum Jump