23 Jet burner - first use questions. - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > 23 Jet burner - first use questions.

Reply
 
Thread Tools
Old 09-28-2008, 10:32 PM   #1
sleepystevenson
Recipes 
 
Oct 2007
North Western PA
Posts: 435
Liked 13 Times on 7 Posts



Hey everybody,

Just fired up the new one barrel single tier system yesterday. Got all the sight glasses calibrated....93 gallons....one at a time....you know how it goes... the definition of tedium... However,

The pinstriping worked great! Will post some pics soon.

After cleaning of everything and calibration, we wanted to do a "wet run" with water, to see how the burners would work, as well as see how long it took to boil / cool water before doing our first brew.

Well....30 gals of water....1 hr 30 mins to boil (from a starting temp of 60*). Seemed like a long time for a 175,000 BTU burner.

I would say, based on other threads I have read here, that the burner wasnt' exactly where it should be, height wise. Too close to the bottoms of the 1 barrel kegs, perhaps?

The flame looked nice and blue for the most part, but at the top, closest to the bottom of the keg, it was orange/yellow standard flame looking, and much larger/taller than the blue jet flames. Didnt happen on every jet, or all the time, but kinda hit and miss. I am sure this is affecting my efficiency, and I am not getting all out of the burner as I could. Any suggestions or thoughts?

Maybe the carbon dioxide is getting trapped around the curved bottom of the kegs and the "apron" base and I am not getting enough oxygen. From the lowest point in the center of the keg, it is about 6" to the top of the jet burner tips. It is about 4.5" from the lowest point of the lower keg apron to the tip of the jets.

Will try to get some pics when I get a chance. My thoughts are to lower the burner a bit and try again. Or, to drill some more holes in the bottom apron to allow the gas to vent. Maybe my gas supply is not adequate?? I don't think that is the case, however.

Thanks!!



 
Reply With Quote
Old 09-29-2008, 12:23 AM   #2
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,152
Liked 1622 Times on 1050 Posts


Sometimes when my burner throws a bit of orange flame, blowing across it briskly purges the pillow of co out from under the keg. It doesn't happen to me often but it always works.
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 09-29-2008, 02:55 PM   #3
sleepystevenson
Recipes 
 
Oct 2007
North Western PA
Posts: 435
Liked 13 Times on 7 Posts


I had about a half inch adjustment in the burners, so I lowered them as much as possible.

I will try blowing under them next time I fire them up. I have a small fan I could place close to the brewstand, if that solves the problem.

Thanks, Bobby.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Burner questions rhltechie Equipment/Sanitation 3 08-19-2009 03:34 PM
burner questions??? Firry15 Equipment/Sanitation 8 04-10-2009 06:30 AM
I need heat! Burner questions. ScottyT Beginners Beer Brewing Forum 10 02-06-2009 04:51 PM
Kettle/Burner questions Edcculus Equipment/Sanitation 1 06-26-2008 06:52 PM
keggle + burner questions Bobby_M Equipment/Sanitation 6 03-12-2007 02:00 PM


Forum Jump