Missed Pre-Boil Volume - Home Brew Forums
Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Missed Pre-Boil Volume

Reply
 
Thread Tools
Old 06-29-2008, 04:14 PM   #1
brew hoperator
 
brew hoperator's Avatar
Recipes 
 
Jan 2008
Reading, PA
Posts: 305
Liked 4 Times on 4 Posts



My brewsmith recipe calls for a 7 gal pre-boil volume and after I mashed and double batch sparged I only got 6.25ish of pre boil wort. I double checked my water measurements and everything was right. Let me go into how how sparged:

after the mash, I vorlaufed, and drained. I then added the split amounts of batch sparges volume at 180F each and let it settle for 5 minutes and then drained at a very slow rate. I did this process the same for both batch sparges.

By letting it settle and drain for a longer time, would this be the reason for the low pre-boil amount?

 
Reply With Quote
Old 06-29-2008, 04:25 PM   #2
Beerrific
 
Beerrific's Avatar
Recipes 
 
Mar 2007
Georgia
Posts: 5,562
Liked 54 Times on 46 Posts


The settling and slow drain should not effect anything.

There are two reasons for losing volume that I can think of:
1. Water absorption by grain.
2. Loss to dead space in the MLT.

You could post all your volumes (amount in mash, sparge, and in the kettle) and something might stick out.

 
Reply With Quote
Old 06-29-2008, 04:27 PM   #3
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 69,201
Liked 7702 Times on 5413 Posts


No, the length of time wouldn't change the absorption rate of the grain. I am betting that when you set up Beersmith for your system, you didn't have the correct amount of water for grain absorption.

When I sparge, I check the volume of my first runnings. If I have, say, 2.5 gallons, I can see that I need 4 gallons of sparge water to hit my target of 6.5 gallons (absorption only happens the first time). That's a cheap recheck of volume for me.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 06-29-2008, 04:38 PM   #4
brew hoperator
 
brew hoperator's Avatar
Recipes 
 
Jan 2008
Reading, PA
Posts: 305
Liked 4 Times on 4 Posts


My double checking was double wrong. I did not mash with enough water, missed it by .75 gallon! Which is what I was missing in the kettle.

Is there anything I can do after the boil to help this batch? Should I top off with some water?

Thanks!

 
Reply With Quote
Old 06-29-2008, 04:41 PM   #5
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 69,201
Liked 7702 Times on 5413 Posts


You can if you need to- but I'd check my OG first, and see what my IBU/SG ratio is. If your efficiency was poor, you'd be "watering down" your beer. If your efficiency is great, you'd probably want the extra volume.

What is your intended OG and your actual OG, and what is your volume in the fermenter?
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 06-29-2008, 04:41 PM   #6
Beerrific
 
Beerrific's Avatar
Recipes 
 
Mar 2007
Georgia
Posts: 5,562
Liked 54 Times on 46 Posts


Quote:
Originally Posted by jacksonvillebrew View Post
My double checking was double wrong. I did not mash with enough water, missed it by .75 gallon! Which is what I was missing in the kettle.

Is there anything I can do after the boil to help this batch? Should I top off with some water?

Thanks!
Do you still have the grain in the MLT?

I would heat up about a gallon of water and sparge again with that. You could also add the water direct to the kettle but that will drop you gravity. I would check your SG to see if adding the water to the kettle will throw you too far off.

 
Reply With Quote
Old 06-29-2008, 05:01 PM   #7
brew hoperator
 
brew hoperator's Avatar
Recipes 
 
Jan 2008
Reading, PA
Posts: 305
Liked 4 Times on 4 Posts


Quote:
Originally Posted by YooperBrew View Post
You can if you need to- but I'd check my OG first, and see what my IBU/SG ratio is. If your efficiency was poor, you'd be "watering down" your beer. If your efficiency is great, you'd probably want the extra volume.

What is your intended OG and your actual OG, and what is your volume in the fermenter?
I did a mash efficiency calc. and got 74% efficiency.

I am in the middle of the boil now and don't have any volume in the fermeneter
My intended OG is 1.050, my pre-boil SG was 1.044.

Reason: wrong word

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Missed final volume - reboil after fermentation? anth All Grain & Partial Mash Brewing 17 11-26-2013 01:44 AM
Help! Include LME volume in boil volume? bitteral Beginners Beer Brewing Forum 7 05-31-2009 06:30 PM
Missed volume goal and OG Matt Up North All Grain & Partial Mash Brewing 11 08-22-2008 05:44 PM
Second AG, missed final volume and off color davebl All Grain & Partial Mash Brewing 4 06-04-2008 10:37 PM
Missed finla volume - too much water. miatawnt2b All Grain & Partial Mash Brewing 5 11-11-2007 05:59 PM


Forum Jump