Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Cornelius Keg poppit valve question
Reply
 
Thread Tools
Old 02-28-2008, 05:39 PM   #1
RobertHSmith
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
RobertHSmith's Avatar
Recipes 
 
Join Date: Feb 2008
Location: St. Louis, MO
Posts: 107
Liked 1 Times on 1 Posts
Likes Given: 1

Default Cornelius Keg poppit valve question

As I was taking apart my kegs (Pepsi) to sanitize/rebuild, I noticed that one of the poppet valves was a little bit different. There were 3 different ball lock fittings, but all had the same poppit valve except for one.

The two types can be seen in this image from http://hbd.org/carboy/ballkegclean.htm


7 of them are like B, but one is like A. I took a good look at the inside of the ball lock fitting and the tapered part at the top looks the same on all of them.

It seems like the design of the one that isn't like the others will work on any of the ball lock fittings, but I wanted to know if anyone has experience with this type of situation. Do I need to be careful and put the one that is different back into the same ball lock fitting, or does it matter?

and a helpful hint: make sure when releasing the pressure that you release it from the ball lock fitting marked in, not out. Having your eyelashes stuck together with residual syrup is not a pleasant experience.


RobertHSmith is offline
 
Reply With Quote
Old 02-28-2008, 07:23 PM   #2
jfish63
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: OC NY
Posts: 196
Default

wait for an expert but in my experience they are interchangeable.
I release the pressure from the pressure relief valve in the center of the lid.


jfish63 is offline
 
Reply With Quote
Old 02-28-2008, 07:36 PM   #3
wildwest450
Registered User
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2007
Posts: 9,099
Liked 170 Times on 155 Posts
Likes Given: 4

Default

Quote:
Originally Posted by RobertHSmith
and a helpful hint: make sure when releasing the pressure that you release it from the ball lock fitting marked in, not out. Having your eyelashes stuck together with residual syrup is not a pleasant experience.
Or you could use the pressure relief valve.
wildwest450 is offline
 
Reply With Quote
Old 02-28-2008, 07:38 PM   #4
RobertHSmith
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
RobertHSmith's Avatar
Recipes 
 
Join Date: Feb 2008
Location: St. Louis, MO
Posts: 107
Liked 1 Times on 1 Posts
Likes Given: 1

Default

Quote:
Originally Posted by wildwest450
Or you could use the pressure relief valve.
you know, i thought of that after I got sprayed
RobertHSmith is offline
 
Reply With Quote
Old 02-28-2008, 08:08 PM   #5
wildwest450
Registered User
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2007
Posts: 9,099
Liked 170 Times on 155 Posts
Likes Given: 4

Default

As far as I know poppets are not interchangeable, I would either put that one back in the same place or replace it with the proper one. When I rebuilt mine I replaced all the poppets, their expensive but it's worth it not to have your beer leaking all over the floor. This site tells which poppet goes to which keg. http://www.chicompany.net/index.php?...dex&cPath=3_14 They also have decent prices.
wildwest450 is offline
 
Reply With Quote
Old 02-28-2008, 11:35 PM   #6
malkore
Feedback Score: 0 reviews
 
malkore's Avatar
Recipes 
 
Join Date: Jun 2007
Location: Nebraska
Posts: 6,922
Liked 34 Times on 32 Posts
Likes Given: 9

Default

Williams Brewing has all 4 of these poppets and their page lists which poppet goes with what keg.

I believe true Cornelius kegs were all the same poppet. I believe there are two types of firestone (pin-lock) keg poppets, and the 4th is a cornelius clone.

you do wanna have the right poppet for the right keg brand for reliability and proper seals.
__________________
Malkore
Primary: English Mild
On tap: Pale Ale, Lancelot's Wheat, English Brown Ale, Steam Beer, HoovNuts IPA
Bottled: MOAM, Braggot, Raspberry Melomel, Merlot, Apfelwein, Pyment, Sweet mead, Cabernet
Gal in 2009: 27, Gal in 2010: 34, Gal in 2011: 13, Gal in 2012: 10
malkore is offline
 
Reply With Quote
Old 03-01-2008, 02:23 AM   #7
RobertHSmith
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
RobertHSmith's Avatar
Recipes 
 
Join Date: Feb 2008
Location: St. Louis, MO
Posts: 107
Liked 1 Times on 1 Posts
Likes Given: 1

Default

Ok,

I lined up all of the plugs and poppets and noticed something, they are all basically the same height and the one poppet that is different was in a plug that was the same as 4 of the other plugs that had the cornelius stlye of poppet, or the one with the thickest rubber seal, type B from the image.

I'm no engineer but, it appears that the only issue would be if I used a shorter poppet with a longer plug. The diameter of the holes at the top and the taper appear to be the same, although I arrived at that conclusion by the very un-scientific eye-ball method.

RobertHSmith is offline
 
Reply With Quote
Old 03-05-2008, 02:31 AM   #8
RobertHSmith
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
RobertHSmith's Avatar
Recipes 
 
Join Date: Feb 2008
Location: St. Louis, MO
Posts: 107
Liked 1 Times on 1 Posts
Likes Given: 1

Default

Looks like I'll be ordering poppet valves. The one odd poppet isn't working out. Although it seals, it won't depress enough to get the quick disconnect on. Ugh.

I could modify it with a dremel, but think it will be better in the long run to jus order new ones...
RobertHSmith is offline
 
Reply With Quote
Old 03-05-2008, 03:00 AM   #9
mr x
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2007
Location: Mainly Halifax
Posts: 1,589
Liked 3 Times on 3 Posts

Default

I just replaced some poppits on a used keg I just bought. The keg has ball lock posts and somebody jammed two longer poppits (similar to type D) in them. When they tightened the posts it drove the three poppit legs into the dip tubes and crimped them and mangled the o-ring.

I pounded the dip tube lip flat and went with the type A poppits, which is all I could get local. I just pressurized the keg and it seems to hold pressure fine.


__________________
This place really went to hell. Follow the OF standard stout. Bye.
mr x is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Grrrrrr, flippin poppit valves! JoeMama Bottling/Kegging 4 02-28-2009 10:57 PM
Why is my Cornelius reg leaking from the spring valve? jaidexl Bottling/Kegging 7 08-08-2008 07:24 PM
Another Cornelius Keg Question - Gluing Handles back on RobertHSmith Equipment/Sanitation 13 04-08-2008 02:01 AM
Cornelius keg question furniture_guy Beginners Beer Brewing Forum 4 11-11-2006 05:26 AM
CO2 valve question winter999 Bottling/Kegging 3 09-01-2006 06:06 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS