Professional lauter tuns... - Home Brew Forums
Home Brew Forums > Home Brewing Beer > General Beer Discussion > Professional lauter tuns...
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 02-16-2008, 05:05 AM   #1
SayWhat1
Recipes 
 
Feb 2007
Seaside, CA
Posts: 64


Why do they have rakes? I always thought the whole point of lautering was to get the grain bed to act as a filter. Wouldn't running a rake through it be counterproductive?

Quote:
Originally Posted by Wikipedia
A quality lauter tun has rotating rake arms with a central drive unit. Depending on the size of the lauter tun, there can be between two and six rake arms. Cutting blades hang from these arms. The blade is usually wavy and has a plough-like foot. Each blade has its own path around the tun and the whole rake assembly can be raised and lowered. Attached to each of these arms is a flap which can be raised and lowered for pushing the spent grains out of the tun. The brewer, or better yet an automated system, can raise and lower the rake arms depending on the turbidity (cloudiness) of the run-off, and the tightness of the grain bed, as measured by the pressure difference between the top and bottom of the grain bed.
Found that on Wikipedia and it sounds to me like it's just to prevent a stuck sparge, but I didn't think that stuck sparges are that much of a problem if you were careful. Maybe because of the amount of grain they're working with they have to be more careful with their grain beds compacting? Or is it just to make it easier to get the spent grain out of the tun?



 
Reply With Quote
Old 02-16-2008, 05:18 AM   #2
ohiobrewtus
 
ohiobrewtus's Avatar
Recipes 
 
Nov 2006
Ohio
Posts: 7,746
Liked 62 Times on 54 Posts


I could be wrong, but I think that a bit of agitation aids in extracting the maximum amount of fermentables from the malt. The arms also aid in cleaning of the mash tun.


__________________
Quote:
Originally Posted by the_bird
Well, if you *love* it.... again, note that my A.S.S. has five pounds.

 
Reply With Quote
Old 02-16-2008, 05:28 AM   #3
SayWhat1
Recipes 
 
Feb 2007
Seaside, CA
Posts: 64

I thought that was the reason for the long sparge, to maximize sugar extraction. Also, wouldn't disturbing the grain bed like that promote channeling and negate the filtering aspect?

I'm usually pretty quick on the uptake of mechanical stuff like this. I don't know why I'm having such a hard time picking this up...

 
Reply With Quote
Old 02-16-2008, 02:04 PM   #4
Catfish
Art by David Shrigley
HBT_LIFETIMESUPPORTER.png
 
Catfish's Avatar
Recipes 
 
Jul 2005
Nishinomiya, Japan
Posts: 840
Liked 15 Times on 3 Posts


The rakes only cut into the surface of the grain bed helping to prevent channeling and improve speed of run off. And with the nice ones, when you run them backwards the rake blades swing to the side and pus most of the grain out (beats climbing in there with a snow shovel, although it isn't as much fun a bribing homebrewers to climb in there with a snow shovel).
__________________
鯰 a.k.a. なまず a.k.a. Catfish

 
Reply With Quote
Old 02-16-2008, 08:31 PM   #5
SayWhat1
Recipes 
 
Feb 2007
Seaside, CA
Posts: 64

Ah, ok. That makes sense. The way the always looked to me is that the rakes went all the way to the bottom. Thanks, Catfish.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Anyone have Experience with this guys lauter tuns? Grummle Equipment/Sanitation 6 11-06-2009 01:44 PM
My new Tuns... JamieT Kettles, Mash Tuns & Hot Liquor Tanks 6 05-04-2009 02:53 PM
Some questions about Mash Tuns chefchris Equipment/Sanitation 9 09-08-2008 04:55 PM
What do you think of buying pre-made mash tuns? Jayfro21 All Grain & Partial Mash Brewing 17 11-14-2007 09:02 PM
Suggestions for Mash Tuns Jsta Porter All Grain & Partial Mash Brewing 10 10-24-2007 07:32 AM


Forum Jump