Counterflow Chiller Tutorial - Page 33 - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Chillers & Stir Plates > Counterflow Chiller Tutorial

Reply
 
Thread Tools
Old 11-20-2010, 01:56 AM   #321
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,243
Liked 1691 Times on 1088 Posts


Don't forget to drill the stops out of the reducers. I only left enough tubing sticking out to clamps tubing on or whatever.
__________________
Welcome to BrewHardware.com. I love you.
Corny Keg Dry Hop Canisters $26.50 for limited time
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 11-20-2010, 07:35 AM   #322
Flomaster
 
Flomaster's Avatar
Recipes 
 
Nov 2010
Orange, Ca
Posts: 2,149
Liked 38 Times on 35 Posts


I haven't tried to fit it over the 3/8" copper, but I didn't see a stop inside it its possible the ones I bought didn't have them. I still haven't finished it.

is 20' of copper enough or should I try and get a 25' roll?

-=Jason=-

 
Reply With Quote
Old 11-20-2010, 02:49 PM   #323
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,243
Liked 1691 Times on 1088 Posts


I think the difference between 20 and 25 is negligible for this purpose.
__________________
Welcome to BrewHardware.com. I love you.
Corny Keg Dry Hop Canisters $26.50 for limited time
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 11-20-2010, 06:26 PM   #324
Flomaster
 
Flomaster's Avatar
Recipes 
 
Nov 2010
Orange, Ca
Posts: 2,149
Liked 38 Times on 35 Posts


Cool I'll just hack into my hose and put this beast together. now if only I had a cornie to wrap around. oh wait im picking 10 up tomorrow for $10 a pop.

-=Jason=-

 
Reply With Quote
Old 11-22-2010, 07:00 PM   #325
BendBrewer
 
BendBrewer's Avatar
Recipes 
 
Jan 2010
Bend, Oregon
Posts: 3,134
Liked 77 Times on 59 Posts


Another great one Bobby.

Did I see that the wort in is actually below the wort out when in use? This wouldn't seem to work when gravity fed. Did you illustrate this for using a pump Bobby?

I was going to but a ball valve on the wort out end to prevent the "tube not full of wort" problem. Thinking to open the kettle valve and control the flow with the valve on the chiller. And have the wort "in" HIGHER than wort "out" as I gravity feed.

Am I thinking correctly or completely backwards?

 
Reply With Quote
Old 12-06-2010, 04:25 PM   #326
Flomaster
 
Flomaster's Avatar
Recipes 
 
Nov 2010
Orange, Ca
Posts: 2,149
Liked 38 Times on 35 Posts


well I constructed my CFC last night and let me tell you it was a PITA....

I read a reply in the thread about having both coiled up and just twisting them into each other.

step one wrap hose around corny


step 2 wrap copper around corny to get same coil size.


well it started off easy, I had soapy water inside my hose but a few coils into to mix it became very hard to get the copper inside the hose.

I ended up removing the hose and copper from my corny to give me more wiggle room. well roughly 35-45 minutes later I had copper out both ends. *sorry no photos* well next thing was trying to get my pre-built end pieces over the 3/8". I should have drilled out a wee bit larger hole because it was a PITA to try and put it together.

advise for anyone who is going to build this and hasn't yet.
DO NOT SOLDER YOUR 1/2X1/4 REDUCER UNTIL YOU HAVE YOUR 3/8" COPPER INSIDE OF YOUR RUBBER HOSE.

had I not had my reducer already soldered it would have been very easy to assemble.

sorry no photos of finished product.

but here's where I am at.

I have a keggle with 1/2" ball valve and barb fitting on it. *no pick up tube installed yet* I haven't decided on what direction to go with it. should I just get a piece of 3/8" ID tubing to connect my keggle to my CFC and use hose clamps OR is there a preferred method.

mind you I don't have QD's or tubing at all so im really open for suggestions on how to proceed. would the 1/2" ss QD and silicone tubing be the prefered method of attaching every thing?

I will be getting a pump, but not sure if I'll have one in time for my first brew.

-=Jason=-

 
Reply With Quote
Old 12-06-2010, 05:34 PM   #327
bwiens
Recipes 
 
Aug 2009
Murrieta, CA
Posts: 84

Built mine last night, went smoothly as expected. I added some extras so that I can use camlocks on both the wort in/out and the water in/out. This is a picture from my phone and I will take some close ups of the fittings soon.
__________________
Wiens Brewing Company

 
Reply With Quote
Old 12-07-2010, 02:17 AM   #328
Dgonza9
 
Dgonza9's Avatar
Recipes 
 
May 2010
Evanston, Illinois
Posts: 1,182
Liked 11 Times on 11 Posts


Quote:
Originally Posted by Flomaster View Post
well I constructed my CFC last night and let me tell you it was a PITA....

I read a reply in the thread about having both coiled up and just twisting them into each other.

step one wrap hose around corny


step 2 wrap copper around corny to get same coil size.


well it started off easy, I had soapy water inside my hose but a few coils into to mix it became very hard to get the copper inside the hose.

I ended up removing the hose and copper from my corny to give me more wiggle room. well roughly 35-45 minutes later I had copper out both ends. *sorry no photos* well next thing was trying to get my pre-built end pieces over the 3/8". I should have drilled out a wee bit larger hole because it was a PITA to try and put it together.

advise for anyone who is going to build this and hasn't yet.
DO NOT SOLDER YOUR 1/2X1/4 REDUCER UNTIL YOU HAVE YOUR 3/8" COPPER INSIDE OF YOUR RUBBER HOSE.

had I not had my reducer already soldered it would have been very easy to assemble.

sorry no photos of finished product.

but here's where I am at.

I have a keggle with 1/2" ball valve and barb fitting on it. *no pick up tube installed yet* I haven't decided on what direction to go with it. should I just get a piece of 3/8" ID tubing to connect my keggle to my CFC and use hose clamps OR is there a preferred method.

mind you I don't have QD's or tubing at all so im really open for suggestions on how to proceed. would the 1/2" ss QD and silicone tubing be the prefered method of attaching every thing?

I will be getting a pump, but not sure if I'll have one in time for my first brew.

-=Jason=-
Interesting idea to coil them both first. I straightened my IC and then inserted into the hose. Was pretty easy, really. I used water based lubricant and it went in pretty easily.
__________________
On Tap: Belgian Barrel Aged Barleywine, Da Yooper's Oatmeal Stout, Breakfast Stout, Hop Your Face Off IIPA, Catcher in the Rye Saison, "Wino-head" Nelsin Sauvin Gumballhead.

Bourbon Barrel Duchesse De Bourgnone
Kegged:

Fermenting English Mild

on Deck: Lager?

 
Reply With Quote
Old 12-07-2010, 02:21 AM   #329
Flomaster
 
Flomaster's Avatar
Recipes 
 
Nov 2010
Orange, Ca
Posts: 2,149
Liked 38 Times on 35 Posts


yeah if i had to do it again I'd straighten out the copper coil.

-=Jason=-

 
Reply With Quote
Old 12-07-2010, 03:06 AM   #330
orangehero
 
orangehero's Avatar
Recipes 
 
Apr 2010
Northeast
Posts: 1,746
Liked 302 Times on 190 Posts


What was the problem with soldering the reducer?

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Immersion Chiller Tutorial Video Bobby_M Chillers & Stir Plates 46 04-20-2014 04:28 AM
is there a diy immersion chiller tutorial? amishland Chillers & Stir Plates 12 08-02-2010 12:33 PM
Using a Counterflow Chiller doggage Equipment/Sanitation 13 03-18-2009 05:52 PM
Counterflow chiller, do you have too? Gregg Meyer All Grain & Partial Mash Brewing 2 01-15-2007 06:44 AM


Forum Jump