AG brewing- - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > AG brewing-

Reply
 
Thread Tools
Old 11-28-2007, 05:33 PM   #1
MikeFlynn74
 
MikeFlynn74's Avatar
Recipes 
 
Nov 2007
ANCHORAGE!!
Posts: 3,876
Liked 19 Times on 17 Posts



Ok I wanna make sure I have a handle on this before I take the dive. This is at best a simple step by step.

Once youve picked a recipie and have the equipment the steps should look like the below?

1. mill grain
2. Heat water to 160 and add to the mash tun
3. let sit for reccomended time 45-60min.
4. Drain the water back into the boiling pot making sure to rewash the mash once or twice
? Tae hydrometer reading?
5. Start the boil
6. Add hops
7. Drink lots of previously made beer while boiling new stuff
8. Cool, yeast and rack new wort.
9. Take hydrometer Reading
9. Wait

Excuse me if this has already been asked 900 times

 
Reply With Quote
Old 11-28-2007, 05:35 PM   #2
Soulive
 
Soulive's Avatar
Recipes 
 
Mar 2007
The Middle of NJ
Posts: 4,278
Liked 25 Times on 25 Posts


The water needs to be heated higher than 160F for the mash. Do you have any software? Don't taste the hydrometer reading unless you've cooled it down...
__________________
Cheers!


===================
Green Lane Brewing
===================

Primary = Evan!'s Special Bitter
On Deck = EdWort's Porter / American Amber


EdWort's Haus Pale Ale Count

 
Reply With Quote
Old 11-28-2007, 05:39 PM   #3
MikeFlynn74
 
MikeFlynn74's Avatar
Recipes 
 
Nov 2007
ANCHORAGE!!
Posts: 3,876
Liked 19 Times on 17 Posts


software?

I know hydrometer readings are done at 60

Ive read that different mashes use different temps. Is this wrong? or personal prefrence?

 
Reply With Quote
Old 11-28-2007, 05:44 PM   #4
Funkenjaeger
 
Funkenjaeger's Avatar
Recipes 
 
May 2007
Nashua, NH
Posts: 1,598
Liked 11 Times on 9 Posts


As an oversimplified overview, yeah, that's about right... But if that description is as far as your knowledge goes, you ought to spend more time reading before you actually try brewing your first AG batch.

Quote:
Originally Posted by MikeFlynn74
Ive read that different mashes use different temps. Is this wrong? or personal prefrence?
There's a fair amount to learn about the mash and sparge, and temperature is very important. howtobrew.com has some good info on this, and based on the very elementary question you just asked I highly recommend you spend some time reading. In answer to your question, yes, mash temperatures are very important, it makes a difference in whether you end up with a crisp, dry beer, or a sweet, full-bodied one. Perhaps you should start here:
http://www.howtobrew.com/section3/chapter14.html

You'll want to start with a good recipe that has good detail on the strike water/mash/sparge water temperatures and volumes (I recommend EdWort's Haus Pale Ale recipe, if you're looking for one), and using some brewing software to figure out the volumes/temps helps too.


 
Reply With Quote
Old 11-28-2007, 05:45 PM   #5
eriktlupus
 
eriktlupus's Avatar
Recipes 
 
Jan 2007
Cereal City, USA
Posts: 2,618
Liked 13 Times on 11 Posts


most of the brewware out there has a free trial period. i like beersmith the measurement usually come pretty close as long as i preheat my mlt.
__________________
primary1 :UTOPIA BABY(still searching for it)
secondary:middling bastard ipa
kegged:simcoe blonde, crystal pale ale, yellow jacket golden ale, lemon shandy blonde
DRINKIN DAWG BREWERY
LET'S GO RED WINGS


join michigan mashers here

extraction calculator
grains in pounds(G) X 36(average points per gallon of grains) / batch size in gallons(g) = maximum efficiency(ME)
OG / ME = brewhouse efficiency

 
Reply With Quote
Old 11-28-2007, 05:45 PM   #6
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 69,733
Liked 8010 Times on 5599 Posts


Well, basically yes.

There are a few more little tweaks, though.

1. Yes- right before you use it is best, but do it away from where you're brewing. I buy mine pre-milled, since I don't have a mill.

2. Heat your water to YOUR strike temperature. This depends on many factors- the equipment you're using and what type of beer you're making. For example, today I wanted my mash at 154 degrees and I had 14.5 pounds of grain. So, I used 18.13 quarts of 170.1 degree water to maintain my 154 for one hour in my igloo cooler. Brewing software is a HUGE help for this!

3. Yep!

4. Yes, drain the mashtun. Drain the first few quarts into a pitcher, and gently pour that back into the mashtun without disturbing the mash. This is because the first drainings have bits of husk and are cloudy. The grain bed itself will filter it for you, once it settles. Once it's cleared up, drain it into your boil kettle. Then, close the ballvalve and add your sparge water. The sparge water should be around 168 degrees. Stir well, and then drain that the same way you did the first runnings. You can break your sparge water into two additions and so just use 1/2 the first time and 1/2 the second time.

5. I put my boil kettle on the fire while I'm batch sparging- it helps it to stop enzyme activity, and gets it to a boil faster. Bring it to a boil and wait for the hot break.

6. After the hot break, start your timer and begin your hops additions.

7. Ok- today I'm having coffee, though! I started at 8:00 AM.

8. Cool to 70 degrees as rapidly as possible. Aerate as best as you can- splash, pour, strain, etc. Fill your fermenter. Take the sg.

9. Pitch yeast.

Now, you can add to this if you want. I started doing some different things recently- added a mashout, bought an aquarium pump for oxygen, etc. But that's the basics.

There's a chapter in howtobrew.com called "Your first AG batch" and even if you are using a different recipe, you can follow along with it, and it really helps!
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 11-28-2007, 05:47 PM   #7
ohiobrewtus
 
ohiobrewtus's Avatar
Recipes 
 
Nov 2006
Ohio
Posts: 7,785
Liked 63 Times on 55 Posts


Quote:
Originally Posted by MikeFlynn74
Ok I wanna make sure I have a handle on this before I take the dive. This is at best a simple step by step.

Once youve picked a recipie and have the equipment the steps should look like the below?

1. mill grain
2. Heat water to 160 and add to the mash tun
3. let sit for reccomended time 45-60min.
4. Drain the water back into the boiling pot making sure to rewash the mash once or twice
? Tae hydrometer reading?
5. Start the boil
6. Add hops
7. Drink lots of previously made beer while boiling new stuff
8. Cool, yeast and rack new wort.
9. Take hydrometer Reading
9. Wait

Excuse me if this has already been asked 900 times
Yup, you'll want to heat your waer up a bit more than that to hit your target mash temperates (which is usually between 149-158).

You kind of lost me on #4. You'll want to recirculate (vorlauf) about 2 qt. of your mash (drain it out then pour it back into your MLT on top), then you need to sparge. I double batch sparge. The amount of water required to do this is directly proportional to the amount of malt that you are using.

So after you've mashed for 60 min, vorlauf, then drain to your kettle. Pour in your sparge water (normally around 170F). Some folks here drain immediately, I like to leave it for 10-15 minutes. Vorlauf and drain into your kettle, then sparge one more time and drain into your kettle until you have reached your desired preboil volume.

You can take a hydrometer reading that this point if you would like, but if you're not going to use it to make any gravity adjustments then it probably won't benefit you much.

Cool the wort to pitching temps as quickly as possible. Get it into your primary fermenter, take a hydrometer reading, then pitch your yeast.

If you need to top off with water, make sure that you mix your wort well prior to taking a hydrometer reading.
__________________
Quote:
Originally Posted by the_bird
Well, if you *love* it.... again, note that my A.S.S. has five pounds.

 
Reply With Quote
Old 11-28-2007, 05:47 PM   #8
jdoiv
 
jdoiv's Avatar
Recipes 
 
Mar 2007
Nashville, TN
Posts: 1,152
Liked 1 Times on 1 Posts


Using a software program can help you keep track of things. They also have handy calculators in them to help you determine things like strike temp (the temp of the water before you add grains to achieve the proper mash temp) and temp correction for hydrometer readings.
Sort of nit picky, but I would change 8 to: cool, rack to primary and take hydro reading. Then 9 becomes pitch yeast, put blow off tube/airlock in place.

This way if your gravity is way off, you can add lme or dme before adding the yeast.
__________________
Drinking on the keg: BPA, Brown Ale, Dry Mead, Wee Heavy aged on Oak, CAP
Drinking in the Bottle:
Conditioning:
Fermenting:
Planning:

 
Reply With Quote
Old 11-28-2007, 06:01 PM   #9
MikeFlynn74
 
MikeFlynn74's Avatar
Recipes 
 
Nov 2007
ANCHORAGE!!
Posts: 3,876
Liked 19 Times on 17 Posts


Awesome- This is the kind of info I needed. I know im a bit away from truly understanding but at least im on the right track.

I have 5 months before Im back from Vietnam 2 "electric boogaloo". So I am making sure I get all my ducks in a row.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
All-Grain Brewing with Extract Brewing Equipment (pics) DRoyLenz General Beer Discussion 76 06-30-2014 04:53 PM
hook & ladder brewing co. & Southern Tier brewing starrfish General Beer Discussion 22 12-10-2009 04:46 PM
Basic Brewing Radio - German Brewing History Kaiser General Beer Discussion 8 10-30-2009 01:20 AM
Naked City Brewing invades Double Vision Brewing dblvsn North West Homebrew Forum 13 06-23-2008 03:11 PM
Victory Brewing ~ Downingtown, PA 37 minute brewing tour video SuperiorBrew General Beer Discussion 5 01-23-2008 07:14 PM


Forum Jump