BCS 462 , 4 element, 3 pump, 2 x 50amp circuits - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Electric Brewing > BCS 462 , 4 element, 3 pump, 2 x 50amp circuits

Reply
 
Thread Tools
Old 12-02-2013, 05:48 PM   #1
RazorUK
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Oct 2012
Boise, ID
Posts: 165
Liked 11 Times on 10 Posts



So a little background into my mindset before we get going here......

I started brewing October/ November 2012. I had a Mr Beer kit in my house that I'd never taken the time to look at, so I read the instructions and put that together and started to research more on brewing and found this site......Before the Mr Beer was finished fermenting I had already bought myself some brewing gear on craigslist.....

http://www.homebrewtalk.com/f29/been...ng-bit-368506/

It came with 5 kegs and I was thinking no way will I ever need that many, and thought of selling 2 or 3 of them..... I brewed my first extract batch and enjoyed the process, waited for it to ferment and tasted it and thought I'll never need to go all-grain - this is good enough for me!

Fast forward to March with another 3-4 extract batches under me and I decide I'm going to give all grain a try. I find Biermuncher's Cream of Three Crops recipe and make it, mash temps were all over the place, overshooting, over correcting and generally not having a clue what I am doing! Still I got a great tasting beer from that batch and I was hooked on all grain. I've probably done a dozen or more brews since and have my process down where I get good efficiency and am good with my mash now.

I've acquired more and more kegs, I have about 15 corny's now and I have built my keggle, round cooler mashtun, 2 pumps (soon to be 3), 50ft jamil style immersion chiller and the list goes on and on.




So that brings me to today and my new journey into electric brewing. I've gone through the - I just want to do a rims setup so I can better control the mash, to ooh I love Kal's electric brewery, to where I am at now - BCS462 controlled setup.

http://www.homebrewtalk.com/f170/sho...ml#post5684154

So far I have purchased the ebrewsupply BCS 4 element 2 pump 50amp DIY kit and the BCS462

http://www.ebrewsupply.com/ebrew-kit...s-50a-kit.html

http://www.ebrewsupply.com/designs/5...4-Electric.pdf

Now I could put it together like in the wiring schematic there, but before I actually start throwing it together I've been over-thinking ( I do this alot!) and I think I want to modify my setup before I build it as I only want to build this panel once, and not rejig it down the road.

So I stumbled upon this build which is probably as close to what I want to achieve as anything.

http://www.homebrewtalk.com/f170/bcs...inally-352310/

I have to have my house upgraded from 100amp to a 200 amp service, so whilst I have the electrician coming out I am going to have 2 50 amp circuits put in near where I want the brewery to be in my garage.

In the meantime I want to come up with a wiring diagram that will take my purchased ebrewsupply kit (with some additional components no doubt!) and adapt it to power the following:
  • 3 110v pumps
  • 4 elements (2 elements on each 50amp service that can be powered independently)

I'm not currently going to be using all 4 elements, but want it there for as close to future proofing as I can get myself. What I envision is I plug in one of the 50amp circuits to the panel and I can power the panel, 2 elements and all 3 pumps from it. Then when I upgrade to bigger kettles in the future ( I know it's happening, no point lying to myself!) I'd just plug in the other 50 amp circuit and provide the power to the other 2 elements.

I'd also like to work out getting the BCS462 powered independently of the panel as I want it to control a freezer in the future, I'm not adverse to moving the BCS outside of the panel, but can't quite get my head around what that would entail yet.

I'm also planning on adding 2-3 of these just because I like the display on the panel

https://www.oscsys.com/store/product/188

based on the information from here:

http://wiki.embeddedcc.com/index.php...r_a_display.3F


I'm hoping someone can help me work out the initial wiring so I can build my dream panel and document this build along the way!

Cheers

ElNess Likes This 
Reply With Quote
Old 12-03-2013, 04:10 AM   #2
hatrickwah
Sponsor
HBT_SPONSOR.png
Recipes 
 
Nov 2010
UP, Michigan
Posts: 263
Liked 6 Times on 5 Posts


Just shot you a PM. I haven't had a chance to run browse HBT much, but this caught my eye.

Here's the panel built using a stainless steel box:
50a - 4 elements and more by electricbrewingsupply, on Flickr

Quote:
Originally Posted by RazorUK View Post
So a little background into my mindset before we get going here......

I started brewing October/ November 2012. I had a Mr Beer kit in my house that I'd never taken the time to look at, so I read the instructions and put that together and started to research more on brewing and found this site......Before the Mr Beer was finished fermenting I had already bought myself some brewing gear on craigslist.....

http://www.homebrewtalk.com/f29/been...ng-bit-368506/

It came with 5 kegs and I was thinking no way will I ever need that many, and thought of selling 2 or 3 of them..... I brewed my first extract batch and enjoyed the process, waited for it to ferment and tasted it and thought I'll never need to go all-grain - this is good enough for me!

Fast forward to March with another 3-4 extract batches under me and I decide I'm going to give all grain a try. I find Biermuncher's Cream of Three Crops recipe and make it, mash temps were all over the place, overshooting, over correcting and generally not having a clue what I am doing! Still I got a great tasting beer from that batch and I was hooked on all grain. I've probably done a dozen or more brews since and have my process down where I get good efficiency and am good with my mash now.

I've acquired more and more kegs, I have about 15 corny's now and I have built my keggle, round cooler mashtun, 2 pumps (soon to be 3), 50ft jamil style immersion chiller and the list goes on and on.




So that brings me to today and my new journey into electric brewing. I've gone through the - I just want to do a rims setup so I can better control the mash, to ooh I love Kal's electric brewery, to where I am at now - BCS462 controlled setup.

http://www.homebrewtalk.com/f170/sho...ml#post5684154

So far I have purchased the ebrewsupply BCS 4 element 2 pump 50amp DIY kit and the BCS462

http://www.ebrewsupply.com/ebrew-kit...s-50a-kit.html

http://www.ebrewsupply.com/designs/5...4-Electric.pdf

Now I could put it together like in the wiring schematic there, but before I actually start throwing it together I've been over-thinking ( I do this alot!) and I think I want to modify my setup before I build it as I only want to build this panel once, and not rejig it down the road.

So I stumbled upon this build which is probably as close to what I want to achieve as anything.

http://www.homebrewtalk.com/f170/bcs...inally-352310/

I have to have my house upgraded from 100amp to a 200 amp service, so whilst I have the electrician coming out I am going to have 2 50 amp circuits put in near where I want the brewery to be in my garage.

In the meantime I want to come up with a wiring diagram that will take my purchased ebrewsupply kit (with some additional components no doubt!) and adapt it to power the following:
  • 3 110v pumps
  • 4 elements (2 elements on each 50amp service that can be powered independently)

I'm not currently going to be using all 4 elements, but want it there for as close to future proofing as I can get myself. What I envision is I plug in one of the 50amp circuits to the panel and I can power the panel, 2 elements and all 3 pumps from it. Then when I upgrade to bigger kettles in the future ( I know it's happening, no point lying to myself!) I'd just plug in the other 50 amp circuit and provide the power to the other 2 elements.

I'd also like to work out getting the BCS462 powered independently of the panel as I want it to control a freezer in the future, I'm not adverse to moving the BCS outside of the panel, but can't quite get my head around what that would entail yet.

I'm also planning on adding 2-3 of these just because I like the display on the panel

https://www.oscsys.com/store/product/188

based on the information from here:

http://wiki.embeddedcc.com/index.php...r_a_display.3F


I'm hoping someone can help me work out the initial wiring so I can build my dream panel and document this build along the way!

Cheers
__________________
Keeping busy brewing & building.

Electric Brewing Supply

My e-Brewery | Keezer Build & Tap Tower Refurbish |Glycol System

 
Reply With Quote
Old 12-04-2013, 02:53 PM   #3
RazorUK
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Oct 2012
Boise, ID
Posts: 165
Liked 11 Times on 10 Posts


Thanks for your pm, I sent you an email.

 
Reply With Quote
Old 12-04-2013, 03:44 PM   #4
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,201
Liked 1658 Times on 1071 Posts


I'm always confused when I see three pumps. When does one need three liquid flows simultaneously? For that matter, when does one need 22,000 watts running at the same time? I've always figured on putting two 5500 elements into the HLT when you have a 50a service available because a simple selector switch and pair of cheap contactors can repurpose the extra amperage to the boil kettle element after the sparge water is hot. The one application for 22,000w simultaneous would be back to back batches, I suppose.
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 12-04-2013, 05:09 PM   #5
RazorUK
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Oct 2012
Boise, ID
Posts: 165
Liked 11 Times on 10 Posts


I agree with most of what you say Bobby. I probably don't need a third pump or all of the elements firing at once 9 out of 10 times I brew.

I just know my wife has been tolerant of my spending on this hobby, but that will run out one day. I have one chance to spend on this portion of my rig and I don't want to redo it later.

An electric rig that can fire all 4 elements and run 3 pumps isn't something I am ever going to outgrow. So whilst she is tolerant I am going to max out my design as I have told her once i am done with this upgrade, I won't need to upgrade anything outside of possibly my kettles and fermenters in the future.

There are also 4 of us that brew together, so having the ability to brew back to back batches is very appealing.

I also like that I can be heating water to clean up when I have the boil going. Hlt upgrade could offset this want I realize.

I'm borrowing some design elements from JonW's design.

http://www.homebrewtalk.com/f51/sing...ed-rig-204705/

I love the simplicity around the water flow and the aesthetics of his design. Mine will be a similar design to his.

 
Reply With Quote
Old 02-20-2014, 01:54 PM   #6
RazorUK
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Oct 2012
Boise, ID
Posts: 165
Liked 11 Times on 10 Posts


Well this is finally about to start getting real!

I have my electrician all scheduled to come out and run my 2 50 amp circuits to my garage. I have pretty much all the goodies from Ryan to build my panel, and I have picked up 2 of my 4 25 gallon pots at this time. Also thinking I will upscale my HLT in size before I get too far along......

Current work is ongoing to get the space I want to brew in prepared, that is taking a little bit longer than I anticipated due to waiting on my shed being installed until the 14th March to make room!

Not too much of a deal though as I am running 2 weeks later for my electrical work. Work on my panel won't start until I get my brew area sorted out though.

 
Reply With Quote
Old 04-06-2014, 06:32 PM   #7
ElNess
Recipes 
 
Jan 2013
Boyertown, PA
Posts: 20


I am starting a very similar build, using 3 55gal SS barrels. Please keep us up to date!
__________________
Raise a glass to good beer!

 
Reply With Quote
Old 04-06-2014, 07:13 PM   #8
Dog House Brew
HBT_SUPPORTER.png
 
Dog House Brew's Avatar
Recipes 
 
Jun 2008
Indiana
Posts: 1,039
Liked 22 Times on 20 Posts


If I had built like this the first time I could have saved a lot of $$$. Although I wouldn't have known how to use it. Look forward to seeing this.
__________________
Are You Going to Drink all That?

 
Reply With Quote
Old 04-07-2014, 08:26 PM   #9
RazorUK
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Oct 2012
Boise, ID
Posts: 165
Liked 11 Times on 10 Posts


Progress is slower than anticipated!

I have the area cleaned up, rough in electric work is complete, but too much other stuff going on for me to make the progress I want to!


A couple of pictures of the brew area

Before shed:

Click image for larger version

Name:	ImageUploadedByTapatalk1396902073.710437.jpg
Views:	624
Size:	45.2 KB
ID:	191644

After shed:

Click image for larger version

Name:	ImageUploadedByTapatalk1396902214.668713.jpg
Views:	624
Size:	50.7 KB
ID:	191645

Electric work:

200 amp service upgrade

Click image for larger version

Name:	ImageUploadedByTapatalk1396902246.780596.jpg
Views:	642
Size:	48.7 KB
ID:	191646

2 x 50 amp 240 outlets & dedicated brewery sub panel:

Click image for larger version

Name:	ImageUploadedByTapatalk1396902322.476201.jpg
Views:	684
Size:	43.0 KB
ID:	191647

Click image for larger version

Name:	ImageUploadedByTapatalk1396902360.494553.jpg
Views:	690
Size:	50.5 KB
ID:	191648

I also have a couple of rough sketches of my control panel at home that I'll attach later!

Next work is insulation and dry walling, but I am probably a month or more out as SWMBO wants the outside of the house painted before I get too preoccupied in the brewery!

 
Reply With Quote
Old 04-08-2014, 01:42 AM   #10
sandyeggoxj
Sponsor
HBT_SPONSOR.png
 
sandyeggoxj's Avatar
Recipes 
 
Jan 2011
Sunshine and Big Holes
Posts: 3,073
Liked 473 Times on 346 Posts


Subscribing to this! I am building a 50-amp 4 element bcs462 panel right now. I would like to eventually merge it into a dual 50-amp panel so that I could run back to back batches and bump up my kettle size to run back to back 1bbl batches.
__________________
Want to make better beer?
Remember this: Measure, Test, Learn.

*Everything I say is fully substantiated by my own opinion

Do you build your own Smokers or BBQs? Find our custom build parts on ebay or on our website!

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
50amp GFI keeps tripping. funkdaddydowd Electric Brewing 9 07-22-2013 06:54 PM
Is this possible? 1 PID, 1 pump, 1 element...but theres a catch... Abhitchc Electric Brewing 7 06-27-2013 12:17 PM
Herms 240V, 2 Element, 2 Pump theknub Electric Brewing 1 02-26-2013 06:16 AM
50amp Plasma Cutter / Torch cripplecreek For Sale 4 07-03-2012 11:17 AM
Auber 2352 PIDs + heating element +pump terrazza Equipment/Sanitation 6 01-06-2011 06:37 PM


Forum Jump