Conical Practices - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Conical Practices

Reply
 
Thread Tools
Old 10-25-2013, 04:16 AM   #1
laughingboysbrew
Recipes 
 
Mar 2013
minneapolis, mn
Posts: 110
Liked 18 Times on 14 Posts



First of all, love my conical...no regrets... The quality of my beer has noticeably improved - not just better, but consistency and things like taking a gravity reading are a 30s process. However, with no other changes, my brewhouse efficiency has gone from +85% down near 60% with almost 0.5 gallon of beer out with dumping trub and another 1 gallon beer left in the fermenter after kegging.

Under my conical, I have a valve, a 2" dia sightglass and then another valve. After pitching yeast, I open up the top valve and let the sightglass fill. After a day, it's mostly full of trub and I dump it via the bottom valve, but a lot of beer comes with (even if I slightly close the top valve). This creates a vacuum and slowly starts to pull blow-off tube liquid up the tube. Lately, I've been hooking up CO2 during the dumping, but it's a hassle to change the blowoff to the CO2 each time I dump. How do commercial breweries do this? (does scale makes it not an issue?)

Any tips on dumping trub/harvesting yeast/etc? Or, should I just scale my 5gal recipes for 8gal boils/7gal ferm batch size?
__________________
serving: Towhead Blonde, Skipping Stone IPA, I2-PA, Buckwheat, Wheatmister Abbey
cask: 1 Year Kellerbier
nitro: Skinned Knee Imp. IPA
fermenting: Skipping Stone IPA
planning: Dopplebock

 
Reply With Quote
Old 10-25-2013, 12:55 PM   #2
TIPA0303
Recipes 
 
Aug 2012
Rockville, Maryland
Posts: 71
Liked 1 Times on 1 Posts


Add a stainless T between the blow off and fermenter. Thread in a ball valve with a house barb. Seal off the blow off (that should already have a valve), open the gas, and pressurize for the trub/yeast push.

 
Reply With Quote
Old 10-25-2013, 10:38 PM   #3
grathan
Recipes 
 
Jul 2010
Albany, NY
Posts: 2,250
Liked 146 Times on 115 Posts


What about fully closing the valve above the sight glass when opening the bottom valve?

 
Reply With Quote
Old 10-25-2013, 11:45 PM   #4
atoughram
Recipes 
 
May 2013
Puyallup, Washington
Posts: 1,688
Liked 241 Times on 181 Posts


I would think that if it's actively fermenting, it would blow any oxygen that back flowed through the blow off out in no time.

A couple of things I've learned:

1) Lift the blow off tube out of the Star San before dumping the trub.
2) Draw about a quart of liquid or so, enough to get clear beer, out of the racking port before dumping it into kegs.
__________________
Clover Creek Brewery, Puyallup WA Home Brewers of Puget Sound
Planning - Something Sinister....
Fermenters - O2
On tap
Centennial Blonde OG 1.040, Carbon River Hefeweizen OG 1.054, SAMM I am IPA 1.069

 
Reply With Quote
Old 10-27-2013, 05:11 AM   #5
laughingboysbrew
Recipes 
 
Mar 2013
minneapolis, mn
Posts: 110
Liked 18 Times on 14 Posts


Thanks TIPA0303. I already have a T which has my temp probe, so I'll just add another with a ball valve. out of curiosity - do the big boys pressurize their fermenters? I have seen ball valves and pressure gauges...just assumed they were monitoring/releasing fermentation "pressure", not adding.

Correct that closing off the top valve, and then the bottom valve creates a chamber of oxygen that bubbles up through the beer. I fixed that by getting the bottom valve...once you open the top valve, you really have to keep it open. My top valve has 5-6 locking positions as well. Ratcheting it down to just barely open has helped...just enough pressure for some beer to flow down, but not so there's a gush/spray of trub everywhere. If I simply lift the blow off tube out of the star san bucket, it will allow O2 in.

 
Reply With Quote
Old 10-27-2013, 06:25 AM   #6
TIPA0303
Recipes 
 
Aug 2012
Rockville, Maryland
Posts: 71
Liked 1 Times on 1 Posts


Yeah, pressurize to about 4-5 psi to drop the yeast out. It could be conical size specific on the pressure, but I'd start with 2-3 psi and increase from there if needed. You want to drain REALLY slow when draining the yeast out so you don't "rat-hole" the trub and cause beer to just channel through before dropping all the yeast out.

 
Reply With Quote
Old 10-27-2013, 06:33 AM   #7
BudzAndSudz
Recipes 
 
Oct 2011
Boulder, Co
Posts: 454
Liked 33 Times on 32 Posts


Quote:
Originally Posted by laughingboysbrew View Post
Thanks TIPA0303. I already have a T which has my temp probe, so I'll just add another with a ball valve. out of curiosity - do the big boys pressurize their fermenters? I have seen ball valves and pressure gauges...just assumed they were monitoring/releasing fermentation "pressure", not adding.

Correct that closing off the top valve, and then the bottom valve creates a chamber of oxygen that bubbles up through the beer. I fixed that by getting the bottom valve...once you open the top valve, you really have to keep it open. My top valve has 5-6 locking positions as well. Ratcheting it down to just barely open has helped...just enough pressure for some beer to flow down, but not so there's a gush/spray of trub everywhere. If I simply lift the blow off tube out of the star san bucket, it will allow O2 in.

I work with 120BBL fermenters and we seal the blow off lines at about 80% attenuation to allow fermentation to build pressure to around 15PSI at the end. This saves us money on CO2 costs because we use endogenous CO2 from fermentation, and also allows us to have positive pressure for yeast/trub drops as well as filtration racking without needing to hook up CO2. However, we always hook a pressure umbilical from the bright tank to the fermenter to keep the head pressures balanced so tanks don't crumple.
__________________
Quote:
Originally Posted by the_trout View Post
Since I cannot dunk a basketball, jack a fastball out of Yankee Stadium or throw a TD pass to win the Superbowl nailing brew day is about as good as it gets.

 
Reply With Quote
Old 10-27-2013, 07:22 AM   #8
zzzzzzzzz
HBT_SUPPORTER.png
Recipes 
 
Aug 2013
Posts: 81
Liked 13 Times on 12 Posts


I'm pretty sure I read that one guy put a quart sized container off the valve he had on bottom of conical. Leaving the valve open during fermentation. All the heavy stuff just settled out to there and he closed the valve and removed the container. This limited his loss to 1 qt or less. The container could be replaced and done again if need be?
I don't have a conical as yet so have no first hand knowledge.
Aloha

 
Reply With Quote
Old 10-29-2013, 01:34 AM   #9
laughingboysbrew
Recipes 
 
Mar 2013
minneapolis, mn
Posts: 110
Liked 18 Times on 14 Posts


Quote:
Originally Posted by zzzzzzzzz View Post
I'm pretty sure I read that one guy put a quart sized container off the valve he had on bottom of conical. Leaving the valve open during fermentation. All the heavy stuff just settled out to there and he closed the valve and removed the container. This limited his loss to 1 qt or less. The container could be replaced and done again if need be?
I don't have a conical as yet so have no first hand knowledge.
Aloha
this is exactly what I was doing with a 2" sightglass. Problem is when you close off the top valve, remove the sightglass and then reattach, there is a chamber of air that is released up into the fermenter when you re-open the top valve. You can avoid this by putting a valve (not pictured) at the bottom and always keep the top valve open...just opening the bottom valve slightly to drain trub/yeast.

Seems though, after 2-3 dumps, a yeast pull, plus gravity checks, I have about 3/4 gallon of waste, plus the gallon or so left in the cone below the racking arm. I guess that's why I got a 14.5gal fermenter...increase batch size.
Click image for larger version

Name:	WP_20131003_21_04_58_Pro.jpg
Views:	426
Size:	28.2 KB
ID:	156828  
__________________
serving: Towhead Blonde, Skipping Stone IPA, I2-PA, Buckwheat, Wheatmister Abbey
cask: 1 Year Kellerbier
nitro: Skinned Knee Imp. IPA
fermenting: Skipping Stone IPA
planning: Dopplebock

 
Reply With Quote
Old 05-18-2016, 10:55 PM   #10
Kirbuno
Recipes 
 
Jan 2010
San Diego, CA
Posts: 38
Liked 1 Times on 1 Posts


I have the same issues and this has got me thinking about options.

Here is the solution I came up with, which seems pretty straight forward and now obvious. This is so easy and I am happy with the way it works. If you supply the top with a bit of C02 pressure no air gets in the fermenter. I first started with a typical sight glass which many of you have. I was never liking the close the dump valve and then replacing it plan as I didn't like the idea of bubbling up into the wort once it started fermentation, even if you messed with trying to purge all the oxygen, just too complicated. Also it was messy.

This is a very simple idea and it works quite well so I had to share. Hope this helps someone.

The photo shows my first round using a brass hose adapter, I have replaced it with a stainless one. You attach a hose to the end and let it fill whatever container you want. You can work out the details of how you want to fill and what container you use but a bottle filler works very well.

It also works well for removing the cold break in the beginning, you only have to remove as much as you want.

I have attached the links to the parts I used here:

http://www.ebay.com/itm/Tri-clamp-X-.../282025907856?

http://www.ebay.com/itm/371337328622...%3AMEBIDX%3AIT

http://www.ebay.com/itm/121825792222...%3AMEBIDX%3AIT

(1/4" Street Elbow)
http://www.ebay.com/itm/1-4-2-Female...-zO3ctxLcbVw3Q

Best,
Click image for larger version

Name:	Yeast Harvester.jpg
Views:	117
Size:	315.5 KB
ID:	354986  

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Experimenting and best practices Flyinghutch Beginners Beer Brewing Forum 2 06-01-2013 04:20 AM
Bad practices or not? nasmeyer Beginners Beer Brewing Forum 1 09-29-2012 06:33 PM
What are your sanitation practices? h22lude Beginners Beer Brewing Forum 20 12-02-2011 06:45 AM
Mashing practices stephelton All Grain & Partial Mash Brewing 18 03-25-2010 08:27 PM
Shipping Best Practices? ThickHead Sampling and Critiquing and Beer Swapping 6 11-11-2009 02:18 PM


Forum Jump