Bad Kitty Brewery eBIAB - Page 4 - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Electric Brewing > Bad Kitty Brewery eBIAB

Thread Tools
Old 09-18-2013, 09:32 PM   #31
Jan 2012
Palm Beach Gardens, FL
Posts: 558
Liked 17 Times on 15 Posts

Originally Posted by raymadigan View Post
Chris, when you BIAB mash is your water to grist ratio high or low. I am certainly not an expert here, just trying to learn. If the ratio is high, lots of water, what pressure are you referring to?
I add all the water for the brew at once, no sparge. I would assume there would be added pressure on the grain bed from the water above, but I could be completely wrong.

As far as the pizza pan, there is no reason to add this. The grain bed is suspended in the kettle. If you put a 30lb grain bill in there, don't think that is 30lbs of pressue weighing down on the heating element. The grain is suspended in the water. Pizza pan is just extra equipment complicating the simplicity of BIAB. BIAB = Bag + Grain + Water. Nothing else is needed. I receive on average 35 (out of 50) on my beers in competitions, nothing medal worthy yet but better then your average bear!

Reply With Quote
Old 09-29-2013, 07:20 PM   #32
Yambor44's Avatar
Nov 2008
Ocala Florida
Posts: 2,108
Liked 86 Times on 57 Posts

Just food for thought here. My system (b4 adding a recirculating pump recently) will pressure lock when draining water/wort from the spigot with the lid on. The Speidel Braumeister system recirculates the entire mash. The Speidel Braumeister also has slots made into the lid! So with our type of BIAB systems with the lid on, you will either need to drill a small hole for air flow or crack the lid slightly during recirculation in order to keep the bag from "pulling" toward the outlet.

Reply With Quote
Old 10-01-2013, 02:55 AM   #33
schwartzr33's Avatar
Nov 2012
Grand Rapids, Michigan
Posts: 49
Liked 7 Times on 6 Posts

Here is an update from yesterday's brew day, Our system is definitely getting more stable.

As you can see from the photos, we added Reflectix (2 layers) to the brew pot. Not surprisingly, this provided enough insulation that the element did not need to fire that often. We also made a hat for the lid. We put the recirc hose in the center of the mash (had previously been putting it on the side, opposite the pickup tube). I think this significantly helped recirculate the hot wort. The next step will be to drill a hole in the lid, so the lid can be all the way on.

The other big improvement was the 16" aluminum pizza screen. I made legs for it with 2.5" machine screws, washers, and finishing nuts. $2.25 per nut! I am relieved to say the screen did not collapse, though the screen is clearly deformed after one use. The legs were placed strategically around the element, and above the pickup tube. The big gaps in the spacing of the legs is because the screen rests on the fittings for the element and the valve. The tabs are a stainless brace, cut in half, to wedge the screen against the sides of the pot, to keep the screen from moving side to side.

The most interesting finding was that we had a vacuum lock throughout the mash. That is presumably why the screen is deformed. We had good luck with the pump running at about 50%, the bag was firmly stuck in place, but we did not drain all of the wort from underneath the screen and we did not have cavitation. Yambor44, the lid was more than a little open. I think the issue is the concrete oatmeal created by the fine mesh bag and the double crushed grain. I wonder if a slightly more coarse bag would allow the wort to flow more easily?

We managed to hold the mash between 151-153 pretty easily, though still with occasional stirring, albeit less stirring than before. We still need to move the RTD to the pump output, to minimize the temperature differences. As it stands, the SV needs to be a few degrees higher than our target mash temp.

Finally, I think we will ditch the pickup tube. I'm not sure it is doing anything except making it easy to pickup trub. We haven't had great luck whirlpooling, but the gunk does settle to the bottom pretty quickly. I'm thinking that without the tube, the valve will sit high enough above the trub after letting it rest for 15 minutes. There's always one more thing to experiment with...
Click image for larger version

Name:	3.jpg
Views:	567
Size:	61.1 KB
ID:	151273   Click image for larger version

Name:	1.jpg
Views:	558
Size:	49.7 KB
ID:	151274   Click image for larger version

Name:	5.jpg
Views:	614
Size:	111.1 KB
ID:	151275   Click image for larger version

Name:	2.jpg
Views:	570
Size:	62.5 KB
ID:	151276  

Reply With Quote
Old 10-01-2013, 10:08 PM   #34
Jan 2010
St Peters Mo, MISSOURI
Posts: 428
Liked 25 Times on 22 Posts

Hi Schwartz,

I have a setup like yours seen here -

I have too struggled with temp fluctuations and pump recirculation issues.

I got a bigger weave bag and went to a single grind (was grinding 3x before ebiab) and used a sparge arm connected to my pump.
I was able to get 1 degree of change between my PID temp and my temps at the top of the kettle.
But I can not leave my mash alone for fear of the dry fire (and I did already ruin one batch and element with a dry fire).
My original thought was I could leave my setup for an hours while mashing and keep spot in temps.... so far that is FAR from the case.

I am have gone back to double grind and not pumping.
I stir every 20 mins or so and insulate the kettle with a blanket, but temp will still stratify by 4-5 degrees after some time.

I have a stir motor on order, and am hoping this will solve all my issues.
As you know... stirring will keep consistent temps and I will have NO dry fire issues.

Not many eBIAB guys seem to use stir motors though?

PJ has great pics of the motor he uses.

any way... thought I would share...
Nice build and good luck.

thanks Kevin

Reply With Quote
Old 10-07-2013, 11:17 PM   #35
schwartzr33's Avatar
Nov 2012
Grand Rapids, Michigan
Posts: 49
Liked 7 Times on 6 Posts

The trials and tribulations continue. The first photo shows the solution we came up with for managing the condensation that drips back into the pot from the ventilation system. We suspended the pot lid for the last 5 minutes of the boil using a bungee. This actually worked really well for keeping condensation from the fan out of the pot. In the future I think we can position it with a slight tilt, beyond the side of the pot, so condensation from under the lid falls to the floor, instead of into the pot.

It's good to start with a positive right? The second photo shows what is left of the pizza screen false bottom. It worked well on the first brew day, but yesterday it failed catastrophically from the weight of the bag. The screws and washers literally tore the aluminum to shreds. Fortunately the bag only got a couple of small holes.

To close on a positive note (sandwich), despite this setback, we had a great brew day. Temperatures were the most steady yet and we had 83% efficiency with a 4-step mash.

Next plan: calling Chad at Arbor Fabricating.
Click image for larger version

Name:	7.jpg
Views:	484
Size:	72.8 KB
ID:	152592   Click image for larger version

Name:	6.jpg
Views:	489
Size:	101.1 KB
ID:	152593  

Reply With Quote
Old 10-08-2013, 12:49 AM   #36
jeffmeh's Avatar
Feb 2009
Posts: 2,161
Liked 212 Times on 182 Posts

OK, how about trying a bag custom-fit so that it cannot reach the element?

Reply With Quote
Old 10-08-2013, 01:17 AM   #37
DrHops's Avatar
Aug 2009
Canton, Georgia
Posts: 320
Liked 26 Times on 25 Posts

I bought a perforated pizza pan and mounted stainless steel bolts, washers and lock nut through it to create a false bottom. It works great and doesn't deform.
On Deck:

1. Dragonfly Wiz (hard lemonade)
2. Dragonfly Blood (strawberry hard lemonade)
3. Alpine Spring clone
5. Belma S.M.A.S.H.

Reply With Quote
Old 10-08-2013, 11:53 AM   #38
schwartzr33's Avatar
Nov 2012
Grand Rapids, Michigan
Posts: 49
Liked 7 Times on 6 Posts

Originally Posted by jeffmeh
OK, how about trying a bag custom-fit so that it cannot reach the element?
That could be an elegant solution, thanks! Ordered a wilserbrewer bag last night, 2-3/4" shorter than the height of the pot, to keep the bag away from the element and the pickup tube. I'll keep you posted.
Bad Kitty Brewery eBIAB

Reply With Quote
Old 10-09-2013, 02:06 AM   #39
Feb 2012
Gainesville, Florida
Posts: 253
Liked 41 Times on 11 Posts

Regarding temperature stratification, it's my opinion, after personal experience, that the PID controllers are not well suited to slow changing systems with lots of thermal mass. The PID over corrects and then it takes a while to cool off and you get these wild swings. If you operate the PID in manual mode and start around 50% and then bump up or down to get your mash in temp you'll find a percentage that works consistently. I run the same PID I use on my brew controller on an oven and it keeps it +\- 1F . By coincidence, the oven has a 5kW heater in it. It would probably work better on a RIMS where the temp sensor was directly down stream of the element. It would tune up better because it could sense and correct faster.

One other thing I did was spread the element out some so it wasn't heating in such a concentrated area. If the fixed part of the element is at 6 o'clock, the free end is bent out to 4 o'clock.

One other suggestion on the PID is to run 100% until you are within 10-20 deg of you mash in temp then turn it over to PID control. That's how the Braumiser Arduino code is written.

Reply With Quote
Old 10-09-2013, 01:18 PM   #40
BIAB Expert Tailor
wilserbrewer's Avatar
May 2007
Jersey Shore, New Jersey
Posts: 9,909
Liked 1586 Times on 1197 Posts

Thanks for the bag order! I shipped yesterday. Just my opinion, but the crushed and mangled pizza screen above was likely caused by the pump suction due to a clogged filter bag, not the weight of the grain. I have no idea what bag material you are using, perhaps turn the pump down. The only time i realized a reduced runoff through a bag, I had a percentage of wheat in the grist. Things I might consider...

1. Throttle back your pump, a trickle should be all you need in a closed system with insulation on the kettle.
2. Using slightly coarser filter / bag material / or less flour in the crush / or use some rice hulls.
3. wrap a piece of pizza screen around the element to make an element guard...not that I think the bag is going to scorch...just a bit of insurance.
4. Heavy duty false bottom.

Good luck solving your issues! You have accurately pointed out why I have neglected to build a fancy E-BIAB system and prefer to keep it ghetto simple making manual temp adjustments and just wrapping the kettle in a large comfortor.

What size batches? I would imagine that large 20 gallon kettle provides a large cooling surface area ratio if only doing 5 gallon batches.

Reply With Quote
Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
My cat wants to be a brew kitty stillbrewin General Chit Chat 11 12-01-2012 06:48 AM
Cowbrau eBIAB brewery build cowgo Brew Stands 14 02-21-2012 09:27 PM
bad kitty! barleyhole Fermentation & Yeast 8 02-09-2010 03:35 PM
Bad Kitty Brown Amiaji Homebrew Ale Recipes 1 07-08-2009 05:39 PM
here kitty kitty beerthirty Drunken Ramblings and Mindless Mumbling 10 07-22-2008 06:40 PM

Forum Jump