Switched from Braided Hose to False Bottom - Big Efficiency Drop - Page 2 - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Switched from Braided Hose to False Bottom - Big Efficiency Drop

Reply
 
Thread Tools
Old 09-05-2013, 01:35 AM   #11
Lumpyyyyy
Recipes 
 
Jan 2012
Methuen, MA
Posts: 229
Liked 4 Times on 4 Posts


I think you may be right. I use beersmith to calculate my values, but I'm pretty sure it's not doing it correctly because of the false bottom thing.

Also, I have a diptube that goes through the center of the false bottom, almost all the way to to the bottom of the keggle. And I batch sparge, so my thought was to drain the keggle as quickly as possible after vorlauf.

 
Reply With Quote
Old 09-05-2013, 03:41 AM   #12
beres47
Recipes 
 
Sep 2013
Posts: 1

Would you have to assume a higher volume of sparge water for your loss under false bottom? I switched to batch sparge with rice hulls an my braid. I still was slightly low on my efficiency a bit.

I have a 20 gal pot and used 1.5 lbs of rice hulls to slightly cover the braid. Would using more hulls and more water factored in for that change make my efficiency change at all? I added 2.5 quarts to my water to factor them in. I have the space for more but I don't want to much water and make my gravity issue worse. Ideas? Resolution?

Thanks

 
Reply With Quote
Old 09-05-2013, 03:49 AM   #13
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,333
Liked 1765 Times on 1122 Posts


The easy way to handle it is to calculate for 1.25qt/lb and then add one gallon for your strike. That way your mash is consistent from batch to batch.

Yes, you are batch sparging but once most of the wort is out, you will lose siphon. Right after that happens, another 1/2 gallon of wort will drip through the false bottom since it was temporarily clinging to the grain. Trust me, if you slow it down towards the end when about another gallon was going to drain out, you'll get more efficient lautering.

There's no reason to change your sparge volume.
__________________
Welcome to BrewHardware.com. I love you.
New Stirplates are IN!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 09-05-2013, 02:56 PM   #14
riored4v
Recipes 
 
Jan 2008
Aurora, CO
Posts: 1,337
Liked 9 Times on 9 Posts


Quote:
Originally Posted by Bobby_M View Post
The easy way to handle it is to calculate for 1.25qt/lb and then add one gallon for your strike. That way your mash is consistent from batch to batch.

Yes, you are batch sparging but once most of the wort is out, you will lose siphon. Right after that happens, another 1/2 gallon of wort will drip through the false bottom since it was temporarily clinging to the grain. Trust me, if you slow it down towards the end when about another gallon was going to drain out, you'll get more efficient lautering.

There's no reason to change your sparge volume.
Would 1 gallon addl strike water be enough to compensate for the amount under the FB? I haven't taken an exact measurement as to how much is under the FB, which is why I'm asking.
__________________
Resistance Brewing Co.
Resist Crap, Drink Craft!

 
Reply With Quote
Old 09-06-2013, 01:48 AM   #15
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,333
Liked 1765 Times on 1122 Posts


Yes, a 15" false bottom sits at the 7/8ths of a gallon mark.
__________________
Welcome to BrewHardware.com. I love you.
New Stirplates are IN!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 09-06-2013, 03:25 PM   #16
riored4v
Recipes 
 
Jan 2008
Aurora, CO
Posts: 1,337
Liked 9 Times on 9 Posts


Quote:
Originally Posted by Bobby_M View Post
Yes, a 15" false bottom sits at the 7/8ths of a gallon mark.
Perfect. Thanks man.

Looking forward to the next brewday now. Hoping between this and a mash out, my effeciency will jump up noticeably.
__________________
Resistance Brewing Co.
Resist Crap, Drink Craft!

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Braided Tube vs. Domed False Bottom vs. Flat False Bottom? ianw58 Equipment/Sanitation 11 09-23-2013 04:45 PM
Braided mash manifold versus a false bottom galacticbrewing12 Equipment/Sanitation 8 10-25-2012 05:09 PM
Issue with false bottom in MLT on first use - should I switch to braided hose? Rev2010 Equipment/Sanitation 4 10-31-2011 11:15 PM
Max Efficiency: Braided hose vs. copper manifold? Zeppman All Grain & Partial Mash Brewing 18 07-18-2010 12:51 AM
False bottom vs. hose braid McCall St. Brewer All Grain & Partial Mash Brewing 4 02-03-2007 09:32 PM


Forum Jump