Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Flaked Oats - Water to Grain Ratio, Sparging Volume, Partial Mash
Reply
 
Thread Tools
Old 08-27-2013, 01:13 PM   #1
nwbrewing32
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2013
Posts: 114
Likes Given: 2

Default Flaked Oats - Water to Grain Ratio, Sparging Volume, Partial Mash

Hello Everyone,

I've been researching for my own recipe on an Oatmeal Stout. It's just about ready for brewing, but I have a question on the mashing water volume. I've seen that I should add 1.25 quarts for every pound of grain. Here are the grains I'm using:

Grain Bill
Pale 2-Row
English Maris Otter
Chocolate Malt
Roasted Barley
Caramel 80L

I am also using 1 pound of flaked oats in the mash - should I be counting that as a specialty grain and adding an additional 1.25 quarts to the mash volume?

Also, is it true you should sparge with the same amount of water as the mashing volume (so if I mash with 5 quarts, I need to sparge with 5 quarts)

Thanks!


nwbrewing32 is offline
 
Reply With Quote
Old 08-27-2013, 02:36 PM   #2
chickypad
lupulin shift victim
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
chickypad's Avatar
Recipes 
 
Join Date: Jul 2010
Location: SF Peninsula
Posts: 3,933
Liked 550 Times on 458 Posts
Likes Given: 227

Default

Count the oats in the total grain bill. Your sparge volume is going to depend on a number of factors such as the size of your grainbill, mash thickness, target boil volume (which will be dependent on your boil off rate). The grain will absorb about 0.5 qt per lb so you can figure out about what your first runnings will be by subtracting the absorption from your mash volume. Then you'll know about how much more you need to sparge to hit target. Or you can just keep sparging until you hit your pre-boil volume.


chickypad is offline
 
Reply With Quote
Old 08-28-2013, 03:05 PM   #3
tnlandsailor
Feedback Score: 0 reviews
 
tnlandsailor's Avatar
Recipes 
 
Join Date: Apr 2005
Location: Knoxville, TN
Posts: 525
Liked 15 Times on 12 Posts

Default

If you have never brewed with flaked adjuncts before, they are gluey as all get out. I stuck a sparge hard and fast once and it was a bugger to get flowing again. It was those darn flaked adjuncts that did it. The fix is to mash in with your grains only, get them good and mixed, then sprinkle the flaked stuff on top. Use a spoon or something to gently submerge them and mix them with just the top few inches of the mash. Everything will convert and you won't have to worry about not having them mixed into the mash at all. The key is to keep them away from your false bottom/manifold where they can gum up the works.
__________________
Prosit!

Hands-On Brewing

Dennis Collins
Knoxville, TN
Innovative Homebrew Solutions
Home of the Hop Stopper!
www.ihomebrewsolutions.com
tnlandsailor is offline
 
Reply With Quote
Old 08-28-2013, 09:15 PM   #4
C-Rider
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
C-Rider's Avatar
Recipes 
 
Join Date: Feb 2011
Location: Wai, Hawaii
Posts: 3,008
Liked 216 Times on 175 Posts
Likes Given: 549

Default

Quote:
Originally Posted by chickypad View Post
Count the oats in the total grain bill. Your sparge volume is going to depend on a number of factors such as the size of your grainbill, mash thickness, target boil volume (which will be dependent on your boil off rate). The grain will absorb about 0.5 qt per lb so you can figure out about what your first runnings will be by subtracting the absorption from your mash volume. Then you'll know about how much more you need to sparge to hit target. Or you can just keep sparging until you hit your pre-boil volume.
INteresting. I loose about .25 qt/gal doing small 2 gallon BIAB. Average grain weight is 4 lbs. Perhaps because I'm doning BIAB and I press every last drop out of my small amount of grain I get less absorption.
__________________
Kaiser Ridge Brewing
-------------------------
Fermenting: Dunkelweizen
Fermenting: SN Celebration Clone
Fermenting:
Bottle Conditioning: German IPA
Bottle Conditioning: Choc/Coffee Stout
Bottled in the refer: SN Celebration Clone
Bottled in the refer:
Bottled in the refer: Am. Pale Ale(3/28)
Bottled in the refer:
Bottled in the refer: Am Imperial Stout(3/11)
Bottled in the refer: GermanImperialStout
C-Rider is online now
 
Reply With Quote
Old 08-28-2013, 10:56 PM   #5
chickypad
lupulin shift victim
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
chickypad's Avatar
Recipes 
 
Join Date: Jul 2010
Location: SF Peninsula
Posts: 3,933
Liked 550 Times on 458 Posts
Likes Given: 227

Default

Quote:
Originally Posted by C-Rider View Post
INteresting. I loose about .25 qt/gal doing small 2 gallon BIAB. Average grain weight is 4 lbs. Perhaps because I'm doning BIAB and I press every last drop out of my small amount of grain I get less absorption.
Good point, OP didn't specify method. My estimate is for what I've seen with non-BIAB systems. Also if BIAB'ing you won't need to worry about the stuck mash issue. I find a handful of rice hulls does the trick for me. I have a false bottom and mash a little on the thin side around 1.5 qt/lb most batches.
chickypad is offline
 
Reply With Quote
Old 08-28-2013, 11:20 PM   #6
C-Rider
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
C-Rider's Avatar
Recipes 
 
Join Date: Feb 2011
Location: Wai, Hawaii
Posts: 3,008
Liked 216 Times on 175 Posts
Likes Given: 549

Default

Quote:
Originally Posted by chickypad View Post
Good point, OP didn't specify method. My estimate is for what I've seen with non-BIAB systems. Also if BIAB'ing you won't need to worry about the stuck mash issue. I find a handful of rice hulls does the trick for me. I have a false bottom and mash a little on the thin side around 1.5 qt/lb most batches.
Funny, I just did an oat meal stout with 6.4 oz flaked oats in total of 4 lbs, the rest all barley. I lost 0.4 gal to this mash. Wonder if the oats took me above my average of 0.25-0.3 gal for 4 lbs of barley.


__________________
Kaiser Ridge Brewing
-------------------------
Fermenting: Dunkelweizen
Fermenting: SN Celebration Clone
Fermenting:
Bottle Conditioning: German IPA
Bottle Conditioning: Choc/Coffee Stout
Bottled in the refer: SN Celebration Clone
Bottled in the refer:
Bottled in the refer: Am. Pale Ale(3/28)
Bottled in the refer:
Bottled in the refer: Am Imperial Stout(3/11)
Bottled in the refer: GermanImperialStout
C-Rider is online now
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Converting Flaked Oats with 2-row, partial mash oatmeal stout nwbrewing32 Recipes/Ingredients 7 07-22-2013 02:36 PM
Partial mash ratio grain and dme/lme tschafer All Grain & Partial Mash Brewing 17 04-05-2013 01:58 AM
Partial Mash-Water to Grain Ratio upperNY01brewer Beginners Beer Brewing Forum 2 06-12-2011 12:04 AM
Water/grain ratio for partial mash? lombard All Grain & Partial Mash Brewing 7 12-19-2010 05:31 AM
Partial mash - what should my water to grain ratio be? bonzombiekitty Beginners Beer Brewing Forum 6 10-27-2009 02:56 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS